cuicuit designed in winknown isubuenit, va resistanceR = 2.8K2 and two identical silicon BITS T1 and 12with 72 and T2 with forward gains BF = 200. Thesupply voltage Vcc =-25 voltsVcc=25 voltsSub-circuitJICAT2IB₁1IB12VIRR = 28K2VIC, 2GINDIB, 1and Ic, s designate the base and collector currentof T2 vespectively where as the courrents IB,₁2 and IG2designate the base and the collector currents of T2respectively. T2 and 12 operate in forward active modeAssume that IB, 1 and IB₁2 are equal · VBE, on = 0.8 molt(Threshold woltage)(a) What is the value of the current IR through vesistance R.?(MA)(b) what is the value of the base vaurrent IB, 1?(MA)(c) what is the value of the collector Ic₁₁?(MA)(d) The evicuit idesigned using Resistance RandTransistors T₁ and To performs an electronic functionto connect to sub circut which function is it?

Answered: Image /qna-images/answer/d90fcc1a-a901-4a66-960e-ca5bf1934e00.jpg

cuicuit designed in winknown subuenit, va resistance R = 2.8K2 and two identical silicon BTTS T₁ and 12 with T₂ and T2 with forward gains BF = 200. The supply voltage Vcc =25 molts Vcc=25 volts sub-circuit √IC ₁1 T2 IBI 1 VIR R = 2.8K2 VIC, 2 GIND IB, 1 and Ic, s designate the base and collector current of T₂ vespectively where as the currents IB₁2 and IG2 designate the base and the collector currents of T2 12 respectively. T2 and 1₂ operate in forward active mode Assume that IB₁1 and 1B₁2 lave equal · VBE, on = 0.8 molt (Threshold woltage, (a) what is the value of the current IR through vesistance R (MA) (b) what in the value of the base current IB,₁1? (MA) (c) what is the value of the collector Ic₁₁? (mA)

cuicuit designed in winknown subuenit, va resistance R = 2.8K2 and two identical silicon BTTS T₁ and 12 with T₂ and T2 with forward gains BF = 200. The supply voltage Vcc =25 molts Vcc=25 volts sub-circuit √IC ₁1 T2 IBI 1 VIR R = 2.8K2 VIC, 2 GIND IB, 1 and Ic, s designate the base and collector current of T₂ vespectively where as the currents IB₁2 and IG2 designate the base and the collector currents of T2 12 respectively. T2 and 1₂ operate in forward active mode Assume that IB₁1 and 1B₁2 lave equal · VBE, on = 0.8 molt (Threshold woltage, (a) what is the value of the current IR through vesistance R (MA) (b) what in the value of the base current IB,₁1? (MA) (c) what is the value of the collector Ic₁₁? (mA)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
The silicon diode's forward voltage is 0.7V. Solve for ia in amperes (4 decimal places if applicable).
Q2) The expected average and RMS output voltage of the following PLECS circuit is equal to Single-phase diode rectifier L: 0.05 01 V_R (V i_N Scope V: 120 w: 2*pi*60 v_N R: 2.50 C: 500e-6 Oa) 40V, 84.85 V Ob) 38 V, 84.85V c) 38V, 80.2V O d) 40V, 38V Probe Probe
Solution of this question is required. Urgently plz.
ANSWER THE QUESTION
For a diode connected NMOS, determine the required drain to source voltage (in V) to produce a drain current of 9.41 µA. Assume the following specifications for the NMOS: k = 6.91 µA/V2, W/L = 7, VTH = 0.9 V, LAMBDA = 0 V-1. Express your answer using 3 decimal places.
VZENER at D1 is 9.3V with an IZENER of 4mA when active. D2 is a silicon diode and the transistor has a β = ∞ and VBE = 0.7V.What is VA? What is VOUT? What is the power dissipated by the diode D1?
Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE= 10 V. Use standard valued 5% resistors and draw a schematic %3D diagram of your design
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
2. Design a clamper circuit to perform the function indicated. Vin th DESIGN Si diodes 10 V -10 V + Vin + Vout Vout 5.7 V -14.3 V
In the circuit shown below, R1 = R2 = 200Q, and the two diodes are identical with VD = 0.7V and Vps =5V. 1. Find output voltage Vo. 2. Find I1, I2, Ipi and Ip2. R1 www Vo Ipi Ip2 Vps
With the given circuit below, if the input voltage is 10 volts peak-to-peak and the diode is silicon, how much is the output voltage in volts on the negative half cycle? (put polarity (+ or -) and values only) + RL out