QI. A vertical shaft is supported by a thrust collar and bearing plate, as shown in Fig. Q1. The average shear stress in the collar must be limited to 18 ksi. The average bearing stress between the collar and the plate must be limited to 24 ksi. Based on these limits, determine the maximum axial load P that can be applied to the shaft. 1.30 in. 0.50 in. 1.0 in

QI. A vertical shaft is supported by a thrust collar and bearing plate, as shown in Fig. Q1. The average shear stress in the collar must be limited to 18 ksi. The average bearing stress between the collar and the plate must be limited to 24 ksi. Based on these limits, determine the maximum axial load P that can be applied to the shaft. 1.30 in. 0.50 in. 1.0 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, P = 20 kN, P, = 16 kN, and P; = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a P: P H K
Current Attempt in Progress The horizontal shaft with a diameter of d = 44 mm is supported by a thrust collar that rests on a 38-mm-thick plate. The thrust collar is 32-mm thick. The thrust collar has an outer diameter of Dcollar = 72 mm. Determine the load P that causes an average shear stress of 89 MPa on the cylindrical surface of contact between the shaft and the thrust collar. Thrust collar area Plate d Thrust collar Dcollar Answer: P = i kN
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.6 MPa. Answer must be in kN/m. Given: b = 110 mm and d = 160 mm. 220 mm 160 mm
Problem 6: For the beam illustrated in the figure, find the locations and magnitudes of the maximum ten- sile bending stress due to M and the maximum shear stress due to V. Dunblom 7. 1.5 kN 0.6 m 2 kN/m A 40-mm-dia. shaft
Consider a circular beam 8 m long and 600 mm in diameter subjected to uniformly distributed load of 30 kN/m as shown in figure. 150 mm 2 m 30 kN/m 6 m B Direct shear stress developed at P will be 0.21 MPa. For analysis of point 'P' which is at AA' section, which of the following statements is/are correct? A Bending stress developed at P will be 4.24 MPa. C Maximum shear stress developed at P will be 4.26 MPa. OI D Maximum shear stress developed at P will be 2.13 MPa. 600 mm
A cylindrical pipe is attached to a wall at one end (A) and is loaded at its other end (B) by two forces, P =500 N. The pipe consists of aluminum with shear modulus G= 27 GPa. The length of the pipe is 3 m and its cross section has outer radius ry=20 mm and inner radius r 15 mm. a) Calculate the twist angle at end B. b) Calculate the maximum shear stress in the pipe. c) Sketch the distribution and direction of the shear stress across the cross section.
For the overhanging beam loaded as shown, determine the maximum values of flexural stress and horizontal shearing stress developed
if the shaft is subjected to ana axial force of 5 kN. determine the bearing stress acting on the collar A. Determine the average shear stress developed on the shear plane on collar A
Please answer with complete free diagrams, etc..
In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB.
1.6
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.