Problem (4.3): A stepped steel shaft AC (G = 12 x 10° psi) is subjected to torsional loads at sections B and C as shown in Figure (4.24). The diameters are: di = 1.75 in. and d2 = 1.0 in. (a) Determine the maximum shear stress in the shaft. Identify the location (s) where this maximum shear stress occurs. (b) Determine the angle of rotation at C, Øc. di Oc d 3000 lb-in. (2) 400 lb-in. 20 in. 10 in. Figure (4.24)

Problem (4.3): A stepped steel shaft AC (G = 12 x 10° psi) is subjected to torsional loads at sections B and C as shown in Figure (4.24). The diameters are: di = 1.75 in. and d2 = 1.0 in. (a) Determine the maximum shear stress in the shaft. Identify the location (s) where this maximum shear stress occurs. (b) Determine the angle of rotation at C, Øc. di Oc d 3000 lb-in. (2) 400 lb-in. 20 in. 10 in. Figure (4.24)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Tb = 80.51
A square post with a tubular cross section is loaded as shown in the figure below. a) Determine the state of the stress at point A having sides parallel to x and y axes. b) Determine the principal planes and principal stresses at point A at the base of the post.
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
The circular shaft shown is subjected to an axial force P at its free end and a compressive force of 50 kips at point B. Note that the shaft is hollow between points A and B. The allowable normal tension stress is 22 ksi, the modulus of elasticity is 29,000 ksi, and the maximum allowable elongation is 0.04 in. Determine the maximum allowable value of P in kips. -0.75 in A B C 50 kips 3 in 20 in 30 in
Within few minutes
Problem 1: Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T=2880 N and T;=432 N. The maximum bending moment is atx= 230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). y 230 mm T, 280 mm 30-mm dia. T C 300 mm 250-mm dia. 400-mm dia. 270 N 1800 N a) Sketch a general shaft layout in 2D (x – y axes), including all components and torques, then calculate all reactions. b) Based on the current shaft dimensions and using only forces at B and C, find the lowest critical speed of the shaft. c) Discard the indicated shaft diameter and use DE-Goodman criteria to determine the critical diameter of the shaft based on infinite fatigue life with a design factor n of 1.5. (Take the same value of endurance limit as that used in…
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
Q.2 A force F is applied to a rigid beam AB. The diameter of the deformable 2х X post AC is 20 mm and diameter of the deformable post BD is 10 mm. A B F= 60 (kN) and x = 1.2 (m) E=70 GPa for the posts AC and BD. 1m 1m C Calculate the followings a) Normal stresses at post AC and BD b) Normal strains at post AC and BD c) Deformations at post AC and BD d) Angle of tilt that occurs in Beam AB.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 2.50 in., the diameter of brass rod (2) is 2.00 in., and the diameter of steel rod (3) is 3.50 in. Determine the axial normal stress in each of the three rods. Assume P = 10 kips, Q = 5 kips, R = 12 kips and S = 22 kips. The normal stress is positive if tensile and negative if compressive.
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tsquare/Tcircle of the shear stresses. Given: r = 11 mm, S = 18 mm, and t = 2.53 mm. S
finding the principle stresses and stress concentration, bending stress, shear stress D D= 0. 375in lin F MA t. 2in F=200lb, W=100lb at the bend
6. Referring to Figure 6, compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. 2 in 6 in FIGURE 6 BC 2 in 10° T