QI) The following PLC program was written to control the operation of a large electric motor- driven pump. A variety of "permissive" inputs protect the pump from damage under abnormal conditions, and one permissive in particular ("valve open") will only allow the pump to start up if one of the valves in the piping system is in the full-open position: Start Valve open Motor (s)- Stop Motor (R)H Bearing temp. Vibration Motor temp. Oil pressure Identify the type of contact (either NO or NC) necessary for each of these electrical switch contacts, based on the trip condition (either high or low) and how each input is applied in the PLC program: 1. Start pushbutton = NO or NC? 2. Throttling valve open limit NO or NC? 3. Stop pushbutton = NO or NC? 4. High bearing temperature NO or NC? 5. High vibration NO or NC? 6. High motor temperature = NO or NC? 7. Low oil pressure NO or NC?

QI) The following PLC program was written to control the operation of a large electric motor- driven pump. A variety of "permissive" inputs protect the pump from damage under abnormal conditions, and one permissive in particular ("valve open") will only allow the pump to start up if one of the valves in the piping system is in the full-open position: Start Valve open Motor (s)- Stop Motor (R)H Bearing temp. Vibration Motor temp. Oil pressure Identify the type of contact (either NO or NC) necessary for each of these electrical switch contacts, based on the trip condition (either high or low) and how each input is applied in the PLC program: 1. Start pushbutton = NO or NC? 2. Throttling valve open limit NO or NC? 3. Stop pushbutton = NO or NC? 4. High bearing temperature NO or NC? 5. High vibration NO or NC? 6. High motor temperature = NO or NC? 7. Low oil pressure NO or NC?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Explain briefly in one(1) sentence what is the function of the squirrel cage winding inthe operation of the synchronous motor.(for 50 points)
Determine the contactor and overload rating for DOL starter of the 99 kW three- phase squirrel cage motor with specification as per below: 415 volts, 50HZ, 1450rpm, 90% efficiency, 0.85 power factor, KVA code H (KVA/HP = 6.7) A relay is an electromagnetic switch that is used to turn on and turn off a circuit by a low power signal, or where several circuits must be controlled by one signal. With aid of illustration, describe the THREE (3) methods to verify the performance of a relay in an electrical circuit. I D Focus O N W
Problem 4 A460V, series motor runs at 500 rpm taking a current of 40A. Calculate the speed and percentage change in torque if the load is reduced so that the motor is taking 30A. Total resistance of armature and field circuit is 0.8 ohm.
20. What is the effect of applying a lower-than-rated voltage to a fractional-horsepower motor?A. The motor will operate with increased magnetizing current.B. The motor will operate satisfactorily at 95% of the rated voltage.C. The motor will heat up dangerously.
25. Which of the following is/are a general method of starting squirrel-cage motors'? a) full voltage starting b) reduced voltage starting c) both "a" and "b" d) neither "a" nor "b"
Motors have many uses. Describe a motor you have experience with. What is it being used for, what power source it uses, and possibly it’s configuration. Explain why you picked this motor and if you have/need to perform(ed) any maintenance on it.
Identify the type of motor used in Washing Machine. With a neat sketch explain its working. List it's advantages and disadvantages.
TYPEWRITTEN ONLY PLEASE UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. THE BIG NUMBER IN THE SIDE IS FOR NUMBERING.
* 12V dc motor can be installed to PLC output pin Directly Via push button Via contactor Via relay
A 300 HP, 208-Volt, 3 – phase motor is started by the Y – Δ method. If the starting current is 54 A, when rated voltage is applied, what current will flow when the Y – Δ switch is used? (A)30 A (B) 31.2 A (C) 32.4 (D) 33.7
Draw the equivalent circuits for each of the following motor types in your logbook: DC Shunt Motor; DC Compound Motors; DC Series Motor. Include for each motor the placement of ammeters and voltmeter to measure input current, armature current and input voltage. Also include a rheostat in the shunt field circuit of the Shunt and Compound motors for the adjustment of no load motor speed.
A 3-phase, 4 pole 50 Hz induction motor provides 20 HP to a load at a speed of 1480 RPM. If the mechanical losses of the motor are assumed to be 0, calculatea. Slip at given speed Answer: .0133b. The developed (or Mechanical) Torque Answer: 14920 Wc. The shaft speed of the motor if the Torque is increased by 125% Answer: 1455 rpmd. The output power at the Torque calculated in part c Answer: 33002.8 W