QI: Determine the magnitude and direction of the friction force which the vertical wall exerts on the 45-Kg block Take 8-15", 45 kg P- 500 N H. -0.50 |He -0.40

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: Q-6: Blocks A and B are identical with each weight of W. If the coefficient of static friction…

A:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: solution incorrect resolve again

A:

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: S0ON so

A:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Figure 3 shows one cart with a mass that is separated from two walls by two springs and a dashpot,…

A:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: can you answer 1B

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: Determine Stres

A:

Q: 2.36x178×106 1- 1 0.9x300x368²×30 Prequired 400 (1.18 30)

A: Given Data⇒

Q: what is 1.54 from?

A: Given:The length of CD is .The length of BC is .The length of AG is The length of AD is .Consider…

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: solve frist one please

A: The diametral pitch of each gear:center distance of the gears:Velocity ratio:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: 200 mm В

A:

Q: what is part number 4

A: Solution:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: D raio s.f.D and B.M.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.