Table Q1(a)LocationLoadNos.Estimated PowerDemand(W)200FactorChandelier lamp10.1Fluorescent lampSSO (13A )Air-conditioner (1HP)Wall lampSSO (13A )Wall lamp360.8Living Hall2500.517500.51360.6Bedroom 12500.5360.6Bedroom 2 Ceiling fan11000.8SSO (13A )Wall lamp2500.51360.6Bedroom 3 wall fan1600.8SSO (13A )Fluorescent lampSSO (13A )Fluorescent lamp2500.51360.8Hall12500.52360.8KitchenExhaust fanSSO (13A )Globe lamp1360.52500.51360.6ToiletWater Heater3k0.3 Q1(a) Table Q1(a) shows a list of electrical appliances for a typical 3 bedroom house. Asan M&E consultant, you are required to plan and design for its development. Withthe coincidence factor (CF) is 0.9, determine:(i) Total connected load (TCL)(ii) Maximum demand (MD)(iii) Total maximum demand (TMD) and maximum current.(iv) Size of MCB and RCCB

“Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

QI (a) Table Q1(a) shows a list of electrical appliances for a typical 3 bedroom house. As an M&E consultant, you are required to plan and design for its development. With the coincidence factor (CF) is 0.9, determine: (i) Total connected load (TCL) (ii) Maximum demand (MD) (iii) Total maximum demand (TMD) and maximum current.

QI (a) Table Q1(a) shows a list of electrical appliances for a typical 3 bedroom house. As an M&E consultant, you are required to plan and design for its development. With the coincidence factor (CF) is 0.9, determine: (i) Total connected load (TCL) (ii) Maximum demand (MD) (iii) Total maximum demand (TMD) and maximum current.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.10P

See similar textbooks

Similar questions

A single-phase half-bridge inverter is connected to a 196V d.c. source. A series connected R-L load has R = 50 ohm, L = 60mH. The inverter frequency is 50HZ. a) Determine the values of the rms load current. b) Calculate the load power. c) Calculate the total harmonic distortion factor (THD) up to the 9th harmonics. d) Calculate the amount of loss caused by harmonics.
Draw a simple block diagram for a 24V stand-alone residential PV system powering both DC and AC loads. Show PV array, inverter, battery bank, charge controller, and AC & DC loads. Show PV array modules wired together as 2 series and 4 parallel (2s x 4p) and show their polarity (+ and – terminals) charging a lead-acid battery bank wired 2s x 8p. Show all major components and conductor polarities. For overcurrent devices and disconnects in the appropriate conductor you can simplify in the appropriate leg and show and as a small combined block labeled:
QUESTION 2a) How would you characterise power bipolar devices in comparison with power MOSFETs? Illustrate your answer by providing unique features of power MOSFETs. b) Using the aid of a MOSFET diagram, explain operational features of the power MOSFET. Support your explanation using MOSFET operation as a switch. Also, illustrate the conditions needed to drive a power MOSFET in the different regions of operation. c) Discuss four (4) advantages of a bridge or half-bridge forward converter when compared with a single-ended forward converter
a-Find the RMS values of the load voltage and the load current b-Calculate and draw the voltage across the load inductance c-Calculate and draw the source current and find its average value
Draw dc load line :
A three phase bridge inverter feeds a star connected load for 180o conduction mode, Rms value of switch current is 10.2 A. For 120o mode calculate the value of switch current.
explain the construction & working principle for 5-stage cascaded voltage multiplier circuit for the generation of HVD.
14. Short-circuit failure mode is associated with microcircuits, transistors, resistors and capacitors. True False
Q5: A three-phase to single-phase, three-pulse cycloconverter delivers power to a load rated at 100 V, 30 A, with power factor 0.8 lagging. Estimate the necessary input voltage and power factor if a, = 0°. 3v3Vm [Hint: The peak output voltage is given by: Vo(peak) cos a].
Maximum dc source current is defined by NEC 690.8(A) as the sum of parallel module rated short circuit currents multiplied by? A.110% B. 125% C. 150% D. 200%
Quiq Plz
Question 5 A three phase bridge inverter is fed from a 500 V DC source. The inverter is operated in 1800 conduction mode and it is supplying a purely resistive, star-connected load with R=15 Q per phase. Determine the: (a) RMS value of phase voltage (b) RMS value of line voltage (c) RMS value of load current (d) RMS and average value of switch current (e) power delivered to the load and (f) the average source current