Qi:(50 marks)Find the total heat flux of the composite wallwhen:BKA = KC = KF = 15m. KKB = KD = 10m. KKE = KG = 20%3Dm. KD.Height of B = C = D4 cm3 cm 4 cm6 cmHeight of F = GAT = 30 K

Answered: Image /qna-images/answer/812a7560-d2fd-4938-af54-1ef52d5e3af4.jpg

Answered: Qi: (50 marks) Find the total heat flux…

Qi: (50 marks) Find the total heat flux of the composite wall when: KA = KC = KF = 15 m. K KB = KD = 10 m. K G KE = KG = 20 m. K Height of B = C = D 4 cm 3 ст 4 cm б ст Height of F = G AT = 30 K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A metal rod of length L=8.88 has only three forces applied to it in the directions shown in the diagram below. Force #2 is applied at the midpoint of the rod. If the rod is in static equilibrium and the magnitude of force #1 is 7.15, what is the magnitude of force #2?
3. Thermal conductivity of a substance is measured as k = k, TIT, . Find an average value for thermal conductivity in the temperature range of T1 and T2. [Ans. = (k, /272 xT} 2 – T}/2) (T2 – T;) 1|
The amount of heat conducted through a wall of length r is given by Fourier's Law:. CONDUCTION RATE EQUATION T FOURIER'S LAW q, = -k A dT dx T, >T, where q, is the heat flux, k is a proportionality factor, Ais the wall's cross-sectional area, and 4 is the temperature gradient throughout the wall. Our friend Matt Labb wants to find T2 (temperature of the wall's rightmost edge) given q,, k, and A. Is this possible? If so, briefly explain how to find Tp. If not, briefly explain why.
no previous attempt please
A bullet is to be tested in the laboratory to determine the drag force on it. Dependent parameter the drag force D (Newton) depends on the velocity of the bullet V(m/s), the length of the bullet L(m), sound velocity c(m/s), density of fluid ρ (kg/m3) and dynamic viscosity µ(kg/ms). Solve the problem by making the necessary assumptions and drawing the schematic figure. I-Determine the nondimensional p parameters using repeating variables ii-a bullet with a speed of 96,2 m/s in air may be modelled in a water tunnel with a test section velocity of 262 cm/s. Determine the length of the model, if the length of the bullet is 56,2 mm. The air and water temperature is 20 oC degree at 1 atm. iii- if the drag force on the model is measured to be 2,62 N, then determine the expected drag force on the bullet. Comment on dynamic similarity equivalence?
Please include each and every expression/formulas
Question 2: Air at the temperature of T1 is being heated with the help of a cylindrical cooling fin shown in the figure below. A hot fluid at temperature To passes through the pipe with radius Rc. a) Derive the mathematical model that gives the variation of the temperature inside the fin at the dynamic conditions. b) Determine the initial and boundary conditions to solve the equation derived in (a). air T1 Re Assumptions: 1. Temperature is a function of onlyr direction 2. There is no heat loss from the surface of A 3. Convective heat transfer coefficient is constant
FN: 76
Completely solve and box the final answer. Write legibly 4. Compute the heat conducted in KW through a sheet of plate glass, k = 0.025 Cal/s-cm-ºC, which is 3.5 m x 4.8 m and 12.5mm thick. The temperature of the surfaces are 28ºC and negative 5.4ºC.
need help engineering of materials
Steam passes at 250 ° C through a steel pipe with an inner diameter of 60 mm and an outer diameter of 75 mm. Pipe The heat transfer coefficients inside and outside are 500 and 25 W / m2K, respectively. Ambient temperature 20 ° C and The heat conduction coefficient of the pipe is 56.5 W / mK. a)Find the heat loss from the 5 m length of the pipe. b)What thickness of material with heat transfer coefficient 0.035 W / mK to reduce heat loss by 95%? insulation should be made.
Please help me