Q/For the circuit of figure below:1- Calculate ST.2- Determine the value of Vout during the period from 0 to.V.0.5 µF+10 VSi56 KN23 V-10 V140 msec ; 3.7 Volt14 msec ; -2.3 Volt14 msec ; -20 Volt14 msec ; 20 Volt140 msec ; 20 Volt140 msec ; 2.3 Volt14 msec ; -3.7 Volt14 msec.; 3.7 Volt140 msec;-3.7 Volt140 msec -20 Volt140 msec; -2.3 Volt

Answered: Image /qna-images/answer/7561f10e-b115-46c3-9ab2-d8d3c3c2de7c.jpg

Q/For the circuit of figure below: 1- Calculate ST. 2- Determine the value of Vout during the period from 0 to. 0.5 µF +10 V IS 56 Kа 3 V -10 V O 140 msec ; 3.7 Volt 14 msec ; -2.3 Volt 14 msec ; -20 Volt 14 msec ; 20 Volt ) 140 msec ; 20 Volt ) 140 msec ;2.3 Volt 14 msec ; -3.7 Volt ) 14 msec.; 3.7 Volt ) 140 msec ; -3.7 Volt ) 140 msec -20 Volt ) 140 msec ;-2.3 Volt

Q/For the circuit of figure below: 1- Calculate ST. 2- Determine the value of Vout during the period from 0 to. 0.5 µF +10 V IS 56 Kа 3 V -10 V O 140 msec ; 3.7 Volt 14 msec ; -2.3 Volt 14 msec ; -20 Volt 14 msec ; 20 Volt ) 140 msec ; 20 Volt ) 140 msec ;2.3 Volt 14 msec ; -3.7 Volt ) 14 msec.; 3.7 Volt ) 140 msec ; -3.7 Volt ) 140 msec -20 Volt ) 140 msec ;-2.3 Volt

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

calculate voltage out
X=5 y =4 YX=54
I need the answer in 20 minutes please
INDUSTRIAL ELECTRONICS 2
low voltage systems10- In which type of circuits is compensation applied to increase the cosƟ angle?a) Activeb)Capacitivec) Inductived) Ohmic
Draw on the graph, DC Voltage Limiting with Zener Diodes ILma IZ (MA) 14 . 05 1287 11.84 10.70 09.61 08.51 07.42 06.33 O 1 2 3 5 6 7
1%AM @ leeeeeeeee 000 ۱۰:۲۷ ص D خاص 3x10^8 m/s The input characteristics of common emitter is between D₂ 5x10^8 m/s O For the following circuit if the secondary voltage of the transformer is 25V rms, the PIV of the diodes are Z 4.5G+ II. IE and IB O IC and VCE O IB and VBE O IB and VCE O Dy * < C₂ Ht 21 docs.google.com *< 1
A half-wave rectifier is connected to a 891Q load in parallel with a capacitor, if the supply frequency is 50HZ, what is the value of the capacitor (in uF) so that the ripple in the output voltage is 10% of .the supply peak voltage اخترأحد الخیارات a. 204 b. 214 c. 247 d. 236 e. 224
+ IR Rs Iz V CA Vi=16V Rz VL=12V a) 14 the load current Iz varies between 0- 2 00 find the values of Rs and RL BYA keep Vz 12 volts. that will constont at b) Calculate power the of the diode. zener
QUESTION 8: A Widlar current source has the configuration shown in the following figure. Assume the bias voltages of V* = 7.5 V and V = -7.5 V. Also assume VBE1 = 0.7 V. Design the circuit such that IREF=1.2 mA and Io=13 µA. Format : 68.642879589768 Format : 3.0902422522623 R1 (kN) RE (kN) V+ Ic2 = lo IREF R1 Ro oVc2 Q2 + + V BEI VBE2 IE2 RE V-
Identify the rule to calculate the average dutput voltage of a single phase full wave fully controlled converter, when connecting with RL load with freewheeling diode and firing angle α -90 O a. (Vm/2n) * (1+ cos a) O b. (2Vm/T) * (1+ cos a) C. Vm/a O d. 2Vm/T
Sketch i and v for the network below for the input shown (Both diodes are Si. V,= 01 0.7 V). Explain your drawings, briefly. 1kO Vo1 20 V lo 5.3V 7.3V -20 V