Q7. For the system shown belowT(s)= 5+10s4+45s3+90s2+164s+200 = 0a. Complete the tableNumber of poles in RHSNumber of poles inNumber of poles in jwLHSb. Do you have special case in this question or not?Decide the stabilityc.Q8 for the Integrating filterV(s)The TF isV (s) (RICIS + 1)(R2C2s + 1)V2(s) (RICIs + )(R2C2s +1).VI(s)RICIVI(s)RICIs + R2C2s(RICIS + )(R2C2s + 1)RICI 2V2(s)d. NoneVIKS)III<>

Answered: Image /qna-images/answer/80eecf3e-a5aa-4f12-a598-a0c759a074b3.jpg

Q7. For the system shown below T(s)= 5+10s4+453+90.2+164s 200 = 0 a Complete the table Number of poles in RHS Number of poles in Number of poles in jw LHS b. Do you have special case in this question or not? e. Decide the stability Q8 for the Integrating filter Vys The TF is V2a) (RICLs +1(R2C2s +1) RICI V20) (RICIS + 1XR2C2+ + 1) c RICIs+ R2C21 V2) (RICIS+)(R2C24 + 1) V) d. None RICI 2

Q7. For the system shown below T(s)= 5+10s4+453+90.2+164s 200 = 0 a Complete the table Number of poles in RHS Number of poles in Number of poles in jw LHS b. Do you have special case in this question or not? e. Decide the stability Q8 for the Integrating filter Vys The TF is V2a) (RICLs +1(R2C2s +1) RICI V20) (RICIS + 1XR2C2+ + 1) c RICIs+ R2C21 V2) (RICIS+)(R2C24 + 1) V) d. None RICI 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

please do 2.2, 2.3, 2.4, and 2.5. Will give like!
Electrical Engineering will upvote . Need matlab knowledge these are the parts that need to be answered. ons: Calculate the cutoff points. Show a screenshot of your circuit. Are the calculated cutoffs being reflected on the theoretical Bode Plot? Include a screenshot of your codes and the theoretical Bode Plot with both cutoff points labelled. How well did the filter perform when processing the 10HZ and 15OHZ combined signal? Include a screenshot of the Scope. The transfer function for the band pass filter is given to you (equation 9). How was this derived? Show the steps starting from how you use the circuit to get the equations representing the circuit to how you solve the equations to get the final version. Given is that it is an RC Bandpass circuit with r1=10kohm, r2= 100kohm ,c1=1uf ,c2=0.001uf. the RC bandpass circuit proceeses 10hz and 150 hz combination. equation 9 needed for part 4 mentioned above is wC1 R Vw? (RCi+R1C2+R2C2)²+(1–w?C,C2R, R2)2 %3D
-3. Determine the Ayquist rate for each of the Co following signals assuming the dyquist. nate for act) is fs Hz. of offs Bad/sec, a) gixel) b) 4₂ (4)= c) (z (t) = d) fult) = dae(t) dz 2<² (t) xelt) cos & fs t
The circuit below; Find the transfer function (VO(s)/VI(s)). What kind of filter is the circuit? Please explain.Find the expression of the cutoff frequency of the filter.( need handwritten only ,otherwise downvote.)
a) Compute the transfer function T(w), the absolute value, and phase at resonant frequency. b) What kind of filter is this? Please answer in typing format please ASAP
For a Low pass filter with a series resistor R = 2 kohms and inductor L = 10 mH with a load resistor RL = 1 kohms, find the: a. transfer function [H(s)] without the load RL b. transfer function [H(s)] with the load RL c. what is the cutoff frequency without the load RL d. what is the cutoff frequency wit the load RL
The transfer function of a first order RC high-pass filter is given below: Draw the circuit representing a RC first [1] order high-pass filter. Clearly show the input and output on the circuit. Proof that the half-power break-frequency of the filter can be described by the equation below (show all steps): fB= 1/2(pi)(R)(C)
15. ..) Given the following Bode plot, what transfer function for H(s) best defines this bode plot? 4018 30d8- 2008. 1000- -10 6 -2018. 14 a 10 d 100 40. (A +100) (+100) (A+109000) -20dB decade C₁ 100 (1 +100,000) 2 (2 +100) (A+1000) 1000 18,000 IF d. 00000 6. 40 (1 +1000) (A+100)ª(2+ 100,000)2 .-40dB de cade 100 (A+1000) (D+100) (A+ 100, 000) d i meg W
uvquvurd Q2 A series RLC bandreject filter is used to reject a 200 Hz sinusoid while passing other frequencies, calculate the values of L and C. Take R=150 Q2 and as 100 Hz. the bandwidth
The center frequency of a bandpass filter that has an upper cutoff frequency of 121 krad/s and a lower cutoff frequency of 100 krad/s is: Select one: O a. None of these O b. 21 krad/s OC. 17.5 kHz O d. 2.79 kHz
explain
Can someone explain how to get Zt of the following bandstop filter?