Q7: What is the compression in the tibia of lengthh = 30 cm of a person of mass m =standing erect? The bone is regarded as a hollow circular tube with internal radius r, = 1.2 cmand external radius r, = 1.75 cm, and Young's modulus along the axis is Y = 2 × 1010N/m².If the maximum tensile strength of tibia is 1.4 × 10®N/m², What is the compression in the tibiaat the point of fracture?80 kg%3DFibula1.Tibia

Data given h= L = 30 cm = 0.3m m = 80 kg r1 = 1.2 cm = 0.012 m r2 = 1.75 cm = 0.0175 m E = 2×…

Q7: What is the compression in the tibia of length h standing erect? The bone is regarded as a hollow circular tube with internal radius r = 1.2 cm and external radius r2 = 1.75 cm, and Young's modulus along the axis is Y = 2 x 1010N/m². If the maximum tensile strength of tibia is 1.4 x 10°N/m2, What is the compression in the tibia at the point of fracture? 30 cm of a person of mass m = 80 kg %3D

Q7: What is the compression in the tibia of length h standing erect? The bone is regarded as a hollow circular tube with internal radius r = 1.2 cm and external radius r2 = 1.75 cm, and Young's modulus along the axis is Y = 2 x 1010N/m². If the maximum tensile strength of tibia is 1.4 x 10°N/m2, What is the compression in the tibia at the point of fracture? 30 cm of a person of mass m = 80 kg %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical rod has initial dimensions of length ? = 4 m andradius ? = 1 cm. When the rod is pulled in tension axially withan external force of ? = 200 kN, the rod deforms to newdimensions of length ?′ = 4.024 m and radius ?′ = 0.998 cm.Determine the modulus of elasticity of the rod and its Poisson’sratio. Assume the rod deforms in the elastic range.
Q;Determine the stiffness and elasticity matrices of the system below:
A normal-weight concrete masonry unit is 40cm by 20cm by 15cm thk. A wall made up of this material, fully grouted and plastered, is supported by a beam. The wall dimension is (H x L) 3m by 5m. The plaster thickness on both wall faces is 15mm. The density of the unit is 21.2 kN/m³, while the density of the grout is 22 kN/m³. Determine the conservative superimposed dead load on the beam in kN/m. Use two decimal places.
ı need solution
The telephone pole AB weighing 3730 N is resting in a hole that is 2m deep. If the contact force between the pole and the edge of the hole is limited to 2500 N, what is the largest safe value of the angle 8 ? 0 12 m 2 m B
1. Rod ABCD is made from two materials with two cross sectional areas. The rod is subjected to axial loads as shown. Neglect the weight of the rod and determine the displacement of point A. EBE Ep =210 Gla 125 kN EAg = 70 GR ABE Aco=900 u AAB = 450 mm 37stEN/ %3D 2m 2.5m
need help asap :<<
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior.
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
A shaft is composed of elements made of S355 with a modulus of elasticity of 2.1×1052.1×105 N/mm² and a Poisson's ratio of 0.3. As shown in the picture, on the right side, there are two forces of 10,000 N each, acting at an angle of 15° upwards, creating a moment that is statically compensated by the force F2 on the left side. The shaft is supported at positions A and B. In the same position (for simplicity), there are two critical cross-sections leading to stress concentrations. The sleeve near F2 is shrink-fitted. The dimensions there are d=50 mm, D=120 mm, and the length of the sleeve is 50 mm. Ha=1 µm and Hn=1 µm. The fit is H7/s6. Determine breell.
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm