Answered: Q7: For the open loop poles shown in…

Q7: For the open loop poles shown in figure s-plane s-o+j w 1- Find the open loop transfer function 2- Sketch the root locus 3- Find the range of the closed loop gain (K) for stable system

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q3- Sketch the root locus of a unity feedback linear time invariant K(s+2) for (s3+5s²+4s) control system of open loop transfer function: positive values of loop gain. s+10
Forthe block diagram given in the figure: Feed forward transfer function G (s) =s + V2. The feedback transfer function is H (s) = s – V2. a) Find the transfer function of the system, Y (s) / X (s). b) Examine the stability of the system. G H
Please show work
Do b)
Q\ Solve the following questions while giving the reason for each point 25. Each RC circuit in an op-amp (a) causes the gain to roll off at -6 dB/octave (b) causes the gain to roll off at-20 dB/decade (c) reduces the midrange gain by 3 dB (d) answers (a) and (b) 26. If a certain op-amp has a midrange open-loop gain of 200,000 and a unity-gain frequency of 5 MHz, the gain-bandwidth product is (a) 200,000 Hz (b) 5,000,000 Hz. (c) 1 x 1012 Hz (d) not determinable from the information 27. The bandwidth of an ac amplifier having a lower critical frequency of 1 kHz and an upper critical frequency of 10 kHz is (a) 1 kHz (b) 9 kHz (c) 10 kHz (d) 11 kHz 28. The bandwidth of a de amplifier having an upper critical frequency of 100 kHz is (a) 100 kHz (b) unknown (c) infinity (d) 0 kHz 29. When negative feedback is used, the gain-bandwidth product of an op-amp (a) increases (b) decreases (c) stays the same (d) fluctuates 30. If a certain op-amp has a closed-loop gain of 20 and an upper critical…
4. PD FB IN- 1 2 3 IN+ 4 8 VS+ 7 6 5 OUT NC VS- Using the Op-Amp diagram shown above, draw a line to create: 4.a. non-inverting amplifier 4.b. Inverting amplifier
R, OV OUT + Complete the analysis showing that Vo/Vin = -Rf/Rin Let currents be defined as 1 equals the current flowing through Rin from left to right 12 equals the current flowing into the Opamp 13 equals the current flowing through the feedback resistor from left to right. Write the KCL equation in terms of 11, 12, and 13 at the inverting node of the Op-Amp. O There is no current flowing in the circuit O 12 = 11 + 13 O 11 = 12 + 13 11 + 12 = 13
10- A unity feedback system has open-loop transfer function G(s)=2/ (S+4), the ratio of time constants of open-loop to closed loop response will be: a- 1:1 b-2:1 c- 3:2 d-2:3 11-First column elements of the Routh's tabulation are 3, 5,-0.75, 0.5,2. It means that there: a- is one root in the left half of s-plane b- are two roots in the left half of s-plane c- are two roots in the right half of s-plane d- is one root in the right half of s-plane 12-An effect of phase-lag compensation on system performance is that: a-for a given relative stability, the velocity error constant is increased b- for a given relative stability, the velocity error constant is decreased c- the bandwidth of the system is increased d- the time response is made faster 13-The phase lead compensation is used to: a- increase rise time and decrease overshoot b- decrease both rise time and overshoot c- increase both rise time and overshoot d-decrease rise time and increase overshoot 14-When phase-lag compensation is…
I need the answer quickly
If A1 = 50 and R1/R2 = 7, the loop gain (k) and the closed loop gain Aq are: Good Replica XF R₁ R₂ and
this question from electronics two course
the sequence of op-amp configurations * : in figure below is R R (a) (b) (c) a- non-inverting op-amp, b- inverting op- amp, c- buffer op-amp a- inverting op-amp, b- buffer op-amp, c- non- inverting op-amp a- buffer op-amp, b- non-inverting op- amp, c- inverting op-amp a- inverting op-amp, b- inverting op-amp, O c- buffer op-amp