Q4) A Wheatstone bridge strain gage, shown in figure 1, with a gage factor (F) of two is used to monitor axial strain in an old train rail. The maximum axial strain is expected to be 200 x 10-5. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 12 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. V supply 5V ΙΚΩ www 1 ΚΩ Gage 350 Ω you 350 £2 Vo V₂ + Instrum op Amp Figure 1 40₁ Vout ADC -Dout

Q4) A Wheatstone bridge strain gage, shown in figure 1, with a gage factor (F) of two is used to monitor axial strain in an old train rail. The maximum axial strain is expected to be 200 x 10-5. The output voltage of the bridge is connected to an instrumentation amplifier before interfacing it with 12 V analog to digital converter. Design a suitable instrumentation amplifier circuit which allows utilization of the full span of the ADC. V supply 5V ΙΚΩ www 1 ΚΩ Gage 350 Ω you 350 £2 Vo V₂ + Instrum op Amp Figure 1 40₁ Vout ADC -Dout

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What 10 Wireless Equipment items need to purchase for a daycare business building?
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
1)The NEC Style Manual indicates that if a term in the NEC appears in more than two articles, it qualifies for a definition in which of the following. a) The articles where the term appears b) Article 90 c) Article 100 d) Table of Contents 2)Definitions of terms related to grounding and bonding and used only in Article 250 are located in ________.a) Article 100 b) Article 200 c) Chapter 9 d) Section 250.2 3)As a general rule, when installing ground rod electrodes, two must be installed always unless a single ground rod provides not more than 25 ohms’ resistance to ground. a) True b) False
Which of the following statements about equipment grounding conductors (EGCS) is true? A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor. B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray. C. No current should be present in the EGC during normal operation. D. EGCs are required to be decreased in size to address voltage drop.
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Can I use a distribution box on every floor to distribute telephone lines to their designated outlets?
QUESTION 3 We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation.
Why did not I find your solution to all my questions ?
Please answer in typing format