Q6. Determine the plastic centroid and also construct the M-N interaction diagram foran non-symmetrical rectangular section with the following properties: the width ofweb b = 300mm, the overall depth h = 550, the effective depth d = 500mm, 4 =1470, A 982, C28/35 concrete and grade 500 steel. The interaction diagramshould consist of at least five data points which should include: (1) the data point forXbal = 0.617d, (2) the data point for zero moment, and (3) the data point for zero axialload.

Answered: Q6. Determine the plastic centroid and…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Estimate the transverse tensile strength of the concrete in Problem 12.6.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
How does a tensile stress differ from a compressive stress?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
Portland cement concrete consists of what four primary elements?
Note For Problems 9.6-1 through 9.6-5, use the lower-bound moment of inertia for deflection of the composite section. Compute this as illustrated in Example 9.7. 9.6-5 For the beam of Problem 9.4-2. a. Compute the deflections that occur before and after the concrete has cured. b. It the live toad deflection exceeds L360 , select another steel shape using either LRFD or ASD.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
Note For Problems 9.6-1 through 9.6-5, use the lower-bound moment of inertia for deflection of the composite section. Compute this as illustrated in Example 9.7. 9.6-2 Compute the following deflections for the beam in Problem 9.2-2. a. Maximum deflection before the concrete has cured. b. Maximum total deflection after composite behavior has been attained.
Note For Problems 9.6-1 through 9.6-5, use the lower-bound moment of inertia for deflection of the composite section. Compute this as illustrated in Example 9.7. 9.6-1 Compute the following deflections for the beam in Problem 9.2-1. a. Maximum deflection before the concrete has cured. b. Maximum total deflection after composite behavior has been attained.

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

Architectural Drafting and Design (MindTap Course…

Civil Engineering

ISBN:

9781285165738

Author:

Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:

Cengage Learning

Construction Materials, Methods and Techniques (M…

Civil Engineering

ISBN:

9781305086272

Author:

William P. Spence, Eva Kultermann

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS