Q6-For a baseband digital system if the sampling rate of the analog basebandsignal is 12KHZ find and compare between bandwidths if we use PCMwith 12 bit code word size, DPCM with difference between consecutivesamples no more than SA and DM.

As we know that bandwidth ( minimum)is equal to the half of bit rate. Bandwidth = n*fs/2

Answered: Q6-For a baseband digital system if the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

[Q2] Different analog signals are sampled at a rate of 26kHz. The samples from these signals are multiplexed via a TDM-PAM system. If these samples are to be transmitted through a channel whose bandwidth is 1.32MHz. (1) What is the maximum number of signals PSM that can be transmitted? (2) If the signals were sampled at the rate 17% over Nyquist, what is the bandwidth of any of these signals?
A continuous time sanal aCt is shown below CG) Aind x[n] with a sampling interval T- O5 and sactch it. Cb) Calculate the energy Ex of the signl (C) Suetch xC3n] and x^) for the DT signal Ex[n) as gou derived in ca). 6o
An analog signal of maximum frequency component of 10 kHz is applied at the input of a PCM system with an uniform quantizer having 32 levels. What will be the Transmission bandwidth of the PCM system? Please answer only if you are confident.
Refer to the pictures for the question
Explain how does LCR circuit work, impedance of LCR circuit in resonance, condition for resonance in LCR circuit and also discuss quality factor in LCR circuit?
2nd problem only
NR value
When the JFET is cutoff, this mean that: Select one: a. The channel is completely closed by the depletion region b. The channel isr everse-biased C. The channel is extremely narrow d. The channel is at its widest point
If the signal to be analyzed is an analog signal, then we pass the signal to an antialiasing filter where B is the bandwidth of the filtered signal. What sampling frequency (Fs) should be used to make this signal discrete/digital?
The Nyquist sampling interval, for the signal sinc(700t) + sinc(500t) is?

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Q6-For a baseband digital system if the sampling rate of the analog baseband signal is 12KHZ find and compare between bandwidths if we use PCM with 12 bit code word size, DPCM with difference between consecutive samples no more than SA and DM. R.