Q6: An AM signal SAM(t)-30[1+0.5cos(4x10't)] a) Carrier frequency c) Modulation index b) fm cos(2n10°t). Determine: d) DSB-SC power e) Bandwidth

Q: d) Briefly explain difference between ADC and DAC?

A: ADC = ANALOGUE TO DIGITAL CONVERTER      DAC = DIGITAL TO ANALOG CONVERTER  Analog digital converter…

Q: If a second order sysytem rise time 3 second ten find a) K= ? (6) dc-offset =! %3D k+1 R(s) → C(s)…

A: Solution in between picture

Q: Discuss briefly the importance of DAC and ADC in electronic communications

A:

Q: For a second order system, %OS (%Peak Overshoot) is 12% and Settling time Ts is 0.6 seconds. Find…

A:

Q: There are two loops in the control system shown in Figure 2. Under Normal operating conditions, the…

A:

Q: I need a complete experience about Dispersion Compensation technique for the optical  fiber…

A: We need to explain about Dispersion Compensation technique for the optical fiber communication using…

Q: Choose the correct answere 1. In tracking control system the initial control effort has a. inimum…

A: According to the question we need to choose the correct option for questions 1, 3, and 5.

Q: 1.Write the difference between PTC, NTC, Thermocouple and RTD. Draw its characteristics.

A: As per the rules we can answer only one question, please post the remaining questions as the…

Q: Explain driven LCR circuit?

A: Explain driven LCR circuit?

Q: b) Draw the graph and describe the relationship between near-end cross talk and attenuation.

A: we need to draw the graph and state the relationship between near end crosstalk and attenuation.

Q: Q4/ Why the performance of multimode graded index is better than multimode step index? Q5/ Design…

A: According to guidelines solving only one question at a time4) To discussWhy the performance of…

Q: A uniform quantizer, with average quantization power of 67.5 mW, is used in a PCM system. 1) What is…

A:

Q: Which of the following is a programmable peripheral interface? Select the correct response: 82A59C…

A: Answer:option:-4 82C55A

Q: How we use the LQG control in Network control System ? Draw the Block diagram of the System.

A:

Q: Draw the equivalent circuits of Class E chopper for the different quadrant operation and write its…

A: The following points should be remembered: 1. Positive Load Current = Current flows from source to…

Q: (a) Describe a time response analysis in a control system. (b) Determine the condition of time…

A:

Q: 2. Look up the Texas Instruments datasheet for LS08 (or SN7408). What is the recommended voltage for…

A:

Q: This is third time that I post it all the given answers are chat gpt or ai was totally wrong. Needs…

A: Superconductivity is a quantum mechanical phenomenon where a material, at very low temperatures, can…

Q: what are the methods of generation AM-SSB

A:

Q: 1) PCB layout of the switch gives Actuator options dimensions and placements Bushing options…

A: The real world demands the analysis and design of complex systems. It is possible with the clear…

Q: iscuss about the overall architecture and structure of a Distributed Control System. Inlcude…

A: DCS is a computerized control system for a process or plant that comprises of a large number of…

Q: Explain in your own words the construction, operation and characteristics of P-Channel JFET with…

A: The major part of this structure is p-type material. It is forming a channel between two n-type…

Q: Analysis of Dispersion Compensation Techniques Used in Optical Fiber Communication

A: We need to Analysis of Dispersion Compensation Techniques Used in Optical Fiber Communication.

Q: Q/why isolator is used in micrpwave bench set up ?

A: An isolator is a two-port device, that transmits microwave or radiofrequency power in one direction…

Q: Draw equivalent ASM chart Representation for the above State diagram. B.

A: The above Given figure is more machine state diagram because output are written inside the state. To…

Q: Why we use the modulation ?

A: The explanation is as follows.

Q: Give two advantages and two disadvantages of Moving Iron instrument over PMMC instrument.

A: -The advantages and the disadvantages of MI metre over PMMC meter are discussed below:

Q: In the control system below, calculate the necessary control poles and PD controller parameters (Kp…

A: We need to calculate the KD and KP values.

Q: 6. What is the effect of c on tr & ess? Why

A: 6) Effect of c on tr:

Q: 4) a) Draw a diagram showing the following circuits 1: Ring, Radial and Spur circuits, label…

A: a) The labeled diagram of the radial circuit is shown below:  The labeled diagram of the spur…

Q: How to test ( good, bad ,leak) of certain SCR and TRIAC using VOM?

A: A SCRis known as silicon controlled thyristor it has four layer which is shown in below figure scr…