DA manometer is rotuted around one leg, as shown. Tbe liquid in theanometer is oil with a spocific gravity of D.82, The differssee in elevationDetween the liquid surfaces in the legs is h=26 cm. The radius of the rotatingacm is r 11 em. What is the speed of rotation [in rad/s]?a) 22.15b) 19.66)21.24d) 18.82e)20.53

Given values: U- tube manometer rotated about one leg. Difference in elevation between liquid in 2…

Q6) A manometer is rotated around one leg, as shown. The liquid in the manometer is oil with a specific gravity of 0.82, The difference in elevation between the liquid surfaces in the legs is h-26 cm. The radius of the rotating nem is r= 11 cm. What is the speed of rotation [in rad/s]? a) 22.15 b) 19.66 c) 21.24 d) 18.82 e) 20.53

Q6) A manometer is rotated around one leg, as shown. The liquid in the manometer is oil with a specific gravity of 0.82, The difference in elevation between the liquid surfaces in the legs is h-26 cm. The radius of the rotating nem is r= 11 cm. What is the speed of rotation [in rad/s]? a) 22.15 b) 19.66 c) 21.24 d) 18.82 e) 20.53

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question
40 - A cylindrical tank with a diameter of 15 cm and a height of 40 cm was filled with water to a height of 25 cm. If the tank is rotated around the vertical axis of symmetry at a constant speed of 20 rad/s, what will be the difference in water height between the edge and the middle of the tank? a) 15cm B) 11.5cm NS) 9.5cm D) 5.4cm TO) 7.2cm
Q7) Air is flowing through a pipe and a mercury manometer is attached with this pipe. If the manometer reads (d = 0.3 cm), determine the 80 mm velocity of air through the pipe. Take pug = umm 13550 kg/m D
A disk with 10 cm radius rolls without slipping down a 30°- inclined plane. At the instant shown, the angular velocity of the disk is w = 5rad/s, CW and its angular acceleration is a = 2 rad/s², CW. Its rightmost end is attached to rod AB (angled 45°) with the length of 24.56 cm. The other end of the rod is attached to collar B that is confined to move along the vertical. (A) Determine the angular acceleration of the rod, (B) Determine the velocity of the rod, (C) Determine the acceleration of collar B at this instant. - 5 rad/ a=2 rad/² r-10 cm 30° 45°
A sphere is fired downwards into a medium with an initial speed of 35.03 m/s. If it experiences a deceleration of a = (-6t) m/s? where t is in seconds, determine velocity of the ball before it stops. %3D
A vertical storage tank with a hemispherical bottom and a cylindrical shell of 6m inside diameter and 6 meter high is filled with water. A sharp-edged orifice 150mm in diameter with C=0.60 is located at the lowest point. Determine the time to empty tone-half of its contents. A 919.82 seconds (B) 951.40 seconds 851.40 seconds 819.82 seconds
A robot arm moves so that P travels in a circle about point B, which is not moving. Knowing that P starts from rest, and its speed increases at a constant rate of 10 mm/s, determine (a) the magnitude of the acceleration when t = 4 s, (b) the time for the magnitude of the acceleration to be 80 mm/s?. %3D 0.8 m В Answer: a. 10.20mm/s? -- --
A 75 mm jet has a velocity of 35 m/s. It strikes a blade moving in the same direction at 20 m/s. The deflection angle of the blade is 150°. Neglecting frictions, calculate:A). The horizontal component of the force exerted by the water on the blade.B). The vertical component of the force exerted by water on the blade.
The motor turns the disk with an angular velocity of o = (5e+ 31) rad/s, where t is in seconds, and it's radius is (150mm). Determine the magnitudes of the velocity when t= 3 s.
180 mm O 15.18 A series of small machine components being moved by a con- veyor belt pass over a 180-mm-radius idler pulley. At the instant shown, the velocity of point A is 280 mm/s to the left and its accel- eration is 80 mm/s to the right. Determine (a) the angular velocity and angular acceleration of the idler pulley, (b) the total acceleration of the machine component at B.
Determine the moment created by the weight of the traffic light about point O. The dimensions of the traffic light post and arm are shown in the accompanying figure. The traffic light weighs 175 N.
H2