Q6/ A car moving on a rough inclined plane are having the following data: Angle of inclination of the plane = 10°; wheel base of the car = 1.8 m; height of C.G. of the car above the inclined plane = 0.9 m; perpendicular distance of C.G. from rear axle = 0.8 m; speed of the car = 36 km/h; µ = 0.6. If the brakes are applied to all the four wheels, determine the distance traveled by the car before coming to rest.

Q6/ A car moving on a rough inclined plane are having the following data: Angle of inclination of the plane = 10°; wheel base of the car = 1.8 m; height of C.G. of the car above the inclined plane = 0.9 m; perpendicular distance of C.G. from rear axle = 0.8 m; speed of the car = 36 km/h; µ = 0.6. If the brakes are applied to all the four wheels, determine the distance traveled by the car before coming to rest.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3) The cart shown below weighs 45o lb (weight located at CG, at geometric center of cart). If the wheels are locked, and the coefficient of static friction between the wheels and the ground is o.4 (), will the cart slide down the hill? Yes/No: 8 ft 3 ft CG 1 ft 6 ft 15
A lever brake system is used to keep a wheel with an applied moment from moving. If the coefficient of static friction is Hs = 0.35 and the dimensions are as given in the parameter table, find the minimum force P that will keep the wheel from moving. BI A Mo value units parameter L1 L2 L3 400 mm 390 mm 30 mm r 140 mm Мо 450 N-m Р-
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm² and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master cylinder cylinder Brake
The coefficient of static friction under the block a and b are the same. If the block is in the verge of sliding, find the tension at each chord. Assume that the pulley is frictionless.Recall [from Physics]:?? = ???Where:?? - is the frictional force?? - is the normal force? -coefficient of static frictiona. Determine the tensile force (lb) on the cable 1.b. Determine the tensile force (lb) on the cable 2. Plsss show complete handwritten solution. Thanksss!!
Figure 2 В A Block A is hanging from a massless string which runs over a massless and frictionless pulley and connects to Block B. Block B slides over an inclined plane with ordinary kinetic friction. The plane under block B is inclined at an angle theta = 0 away from vertical. The other side of Block B is connected to another massless string which runs over another massless and frictionless pulley to connect to Cart C. Cart C rolls without friction over a plane which is inclined at an angle of phi = y away from vertical. C
A single-block brake has the dimensions: cast-iron wheel of D =15 in, a = 32.5 in, 3.. c =10.5 in, e= 6.5 in width of contact surface = 2 in. The brake block lined with molded asbestos, subtends 75º, symmetrical about the center line; it is permitted to absorb energy at the rate of 0.4 hp/in², n = 200 rpm. Assume that p is constant. Compute a) PVm and the approximate braking torque, (b) the force W to produce this torque, (c) the mechanical advantage
O Week6 Friction_21-22.pdf ds/Week6_Friction_21-22.pdf 4. The mine car and its contents have a total mass of 6000kg and a centre of gravity at G. If the coefficient of static friction 10 kN Doo→ between the wheels and the 0.9 m • G tracks is u = 0.4 when the wheels are locked, find the normal force acting on the front wheels at B and the rear /0.15 m A 0.6 m 1.5 m- wheels at A when the brakes at both A and B are locked. Does the car move? [Ans. NA = 16.5 kN, Ng =42.3 kN, the car does not move] ily TWO WAY POWER 09889 NO MODE SETUP
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.