Q5. Describe the following to protect and control the motors: (i) (ii) (iii) Using circuit diagram and the current-time characteristics, explain the motor overload protection by thermal overload relay. Explain using a circuit diagram how the motor will automatic shutdown when input fails? Explain using circuit diagram the under voltage protection of a motor

Q5. Describe the following to protect and control the motors: (i) (ii) (iii) Using circuit diagram and the current-time characteristics, explain the motor overload protection by thermal overload relay. Explain using a circuit diagram how the motor will automatic shutdown when input fails? Explain using circuit diagram the under voltage protection of a motor

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

t OneNote. the letter thats on a. G inspo butter fly roo... S Home Schoology S BAND MS6: Sec 00.. Culminating Event_SRS (5).docx B A A - As safe as school buses are made to be, there are still sometimes accidents which result in collisions. Based on what you have learned about the laws of motion in this unit, you will work as an engineer to develop and present a new design proposal to the local school board to make school buses even safer for their passengers and other vehicles on the road. Your design proposal will need to include the following: An explanation of how each of Newton's Laws of Motion relate to a collision between a bus and a car o How will the bus be impacted based on its mass? o How will the car be impacted based on its mass? o How will the passenger in the car be impacted? o How will the passengers on the bus be impacted? A potential design solution that could make buses safer for passengers and/or other vehicles on the road o An analysis of the costs and benefits of…
Q11
Q17..solve it
A friction experiment is performed on a planet that has the same mass as Earth but half the radius. A 1.0-kg block is pulled along a horizontal dynamics track with a horizontal force of magnitude 15.0 N. If the coefficient of kinetic friction between the block and the track is 0.3, determine the acceleration of the block. O a. 14.26 m/s^2 O b. 12.06 m/s^2 O. 3.24 m/s^2 Od. 15.00 m/s^2
6. A 15kg-particle moves in æyz – plane experience a force of F = 12 N i – 20 N j + 10 N k. Determine the acceleration vector of the particle.
5. A 0.15 kg marble is on a track. It is being held at the top of a hill that is 5 m high. If it is let go, and the bottom of the track is 0.5 m above the ground, find its velocity at the bottom of the track.
7. A bird has a mass of 24 g and perches in the middle of a stretched telephone line. a. Show that the tension in the line can be calculated using the equation T = mg2sine. Determine the tension when b. 0 = 5° and c. e = 0.5°. Assume that each half of the line is straight.
1. You are tasked with designing the runway on an aircraft carrier. The minimum speed for the F/A18 Hornet is 200 mph. The Hornet weighs 40,000 lbf and its twin engines provide a thrust of ~40,000 lbf combined, providing a max acceleration of 1g.a. How long must the deck be to takeoff unassisted? Give the answer in ft. b. This is most likely longer than your typical ~450 ft carrier. What acceleration must you achieve with both the engines and with a catapult system together to reach the required minimum speed by the end of the deck? c. What net force (combined engines and catapult) must be applied to the plane to get the acceleration in b? d. Do you think the plane will be able to use disk brakes on its tires to stop when landing?Use your knowledge of friction to make your argument. Also know that their coefficient of friction is ~1.
Need correctly, all parts. Thank you..
E3
Newton's Laws SET-UP #1: Object with weight W supported by 2 cords as shown. Quantities to Measure: T₁ = -2.2 NOTE: W = mg _N; 01 = NOTE: T₁x = T₁SinØ₁ T₁y = T₁CosØ, T₂x = T₂Sin0₂ T₂y = T₂CosØ2 02 = T2 40 70 02 1. Draw a pseudo-FBD showing the x and y components of T1 & T2.
Dave with a mass of 60 kg goes tubing down a 20 m long hill that has an angle off the horizon of 25º. (Gravity applies) a. He gets a push from the bottom of the hill, so his initial velocity is 2 m/s. How far up the hill will he go before stopping? (there’s no friction) b. He goes back down the hill and then his friend Jill tries to pull him on the tube across a small patch of grass (μk=0.30). If she is pulling parallel to the ground at constant 5 m/s for 5 sec how much power does she expend? c. After climbing back uphill, Dave decided to roll down the hill instead. If he were to be a long cylinder with a radius of 0.1 m, what is his moment of inertia? d. After rolling without slipping down the hill, what is Dave’s final velocity at the bottom of the hill? What is his angular velocity at the bottom of the hill? Dave with a mass of 60 kg goes tubing down a 20 m long hill that has an angle off the horizon of 25º. (Gravity applies) He gets a push from the bottom of the hill, so his…