Q5. [CO1] In fig, given below the input s (t) = m (t), and the amplitude A>> | s (t) |. The twodiodes are identical with resistance r ohms in the conducting mode and infinite resistance in thecut-off mode. Show that output e (t) is given bye(t) =2Rw(t)m(t)r+Rwhere w (t) is switching period sign with period 2n/Wc seconds.a. Hence, show that this circuit can be used as DSB-SC modulator.b. How this circuit can be used as a synchronous demodulator for DSB-SC signal.slope = 1/rs (t)RA coswtids(t)e (t)vds (t)Rw (t)t.t2π-π/2 π2-2n

Answered: Image /qna-images/answer/64db48fb-354a-481f-873e-5aed67a5d1cf.jpg

Q5. [CO1] In fig, given below the input s (t) = m (t), and the amplitude A>> | s (t) | . The two diodes are identical with resistance r ohms in the conducting mode and infinite resistance in the cut-off mode. Show that output e (t) is given by 2R w(t)m(t) r+R e(t) = where w (t) is switching period sign with period 2r/Wc seconds. a. Hence, show that this circuit can be used as DSB-SC modulator. b. How this circuit can be used as a synchronous demodulator for DSB-SC signal.

Q5. [CO1] In fig, given below the input s (t) = m (t), and the amplitude A>> | s (t) | . The two diodes are identical with resistance r ohms in the conducting mode and infinite resistance in the cut-off mode. Show that output e (t) is given by 2R w(t)m(t) r+R e(t) = where w (t) is switching period sign with period 2r/Wc seconds. a. Hence, show that this circuit can be used as DSB-SC modulator. b. How this circuit can be used as a synchronous demodulator for DSB-SC signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer: + There are two questions, first about an ideal diode and then about a modeled diode. For the modeled diode, the voltage across its terminals is 0.7V when it is "on". Which of the following statements are true about the ideal diode above? a. It is possible for i to be positive. b. If i= 0, then v ≤ 0. c. If i > 0, then the diode can be replaced by an independent current source. d. If v = 0, then the diode can be replaced by an independent current source. e. If i = 0, then the diode can be replaced by an independent current source. f. It is impossible for v to be negative. g. None of these statements is true. Enter a single string of letters, in alphabetical order ("abcdef"). V Answer: Which of the following statements are true about the modeled diode above? a. If i= 0, then the diode can be replaced by a open circuit. b. It is possible for i to be equal to 0. c. If v = 0, then i = 0. d. If v<0, then the diode can be replaced by a open circuit. e. If v = 0, then the diode can be…
In the forward bias region, the relationship between the voltage and current of a diode can be evaluated using: O a. None of the answers O b. Ohm's law Oc. Shockley equation O d. Schottky equation
Logic
Please show me how to solve the following practice problems in step by step solution Than you so much!
Course dashboard A diode has 3 mA at 0.6 V and 210 mA at 0.75 V. Find its reverse saturation current (Is) and 1 ideality factor (7). Assume V>Vị and take VT = 25 mV. Uyg Note that because of the approximations, your result might be slightly different than the correct answer. However, it should be very close to it; hence, in that case, simply go for the choice that is closest to your result. Lütfen birini seçin: O A. Is=1.04×10,77-1.99 O B. Is=1.208X10 -10, n=1.41 O C. Is=1.7x10, 7=1.74 O D. Is=2.69×10-8, 7=1.35 O E. Ig=4.27×10-10 7=1.85 OF. Is=11.42x10-1, 7=1.29
Consider the full wave rectifier circuit shown below, with a large smoothing capacitance C = 300µF placed in parallel with the load resistor RL = 1KN and Vm = 15V. Assume that the diodes are piece-wise linear with r,= 100 and V, 0.7V then derive the plot for the output voltage across the load resistor RL. Plot A V Plot C V wm Plot B V Plot D V please pick a plot
For the circuit shown, for what range of Vi(t) will the diode be in the breakdown region. 10k2 V-I characteristic curve Vi(t) 5kfl E D - 5V tout 0.7V O a. Vilt) greater than 9.45V. O b. Vilt) less than 1.7V O c. Vift) less than 2.7V O d. Viſt) less than 3.7V O e. Vit) less than - 26V. O Vit less than -15V. Oo. None of the listed range O h. Vit greater than - 26V. OVit greoter than 3.7V
Consider the following circuit with Vs(t) = 2.0 + 0.02 sin(2 pi t) V,R1 = R2 = 25ohms Idc = 1mA, Vdc = 5V. Assume Vy = 0.7V and VT = 25mV.a) Draw the equivalent circuit under DCb) Determine the DC voltage and current through the diode.c) Draw the equivalent circuit under acd) Determine the total current through the diode
B5
H3
V (+) VT A diode whose terminal characteristics are related as iD = Is current and VT is the thermal voltage (= 25mV), is biased at ID = 2mA. Its dynamic resistance is 9 where Is is the reverse saturation
The original diode equation was derived by William Shockley in 1949 to model the behaviour of germanium diodes. A few years later it was modified to account for the differences between germanium and silicon diodes by including an ideality factor n. This produced the form of the diode equation that you will now be familiar with: eV 1 = 1₁ [exp()-1] 3) Extend your analysis to extract the reverse saturation current under strong forward bias. VD (V) 0.100 0.150 0.200 0.250 0.300 0.350 0.400 0.450 0.500 0.550 0.600 0.650 0.700 lo (A) 7.47E-11 1.93E-10 6.01E-10 1.54E-09 4.26E-09 1.00E-08 2.56E-08 1.78E-07 1.13E-06 6.48E-06 ▬▬▬▬▬▬ 4.71E-05 2.74E-04 1.94E-03