Q5. An output shaft is connected to an electric motor as shown in the following Figure. The shaft rotates at a speed of 1000 RPM and the applied torque is 9.7 N.m. T, T; = 21°C 10 amp Motor 110 V

Q: Q5: a. Draw the single slop ADC b. explain its operation c. state its disadvantages.

A: ADC is a analog to digital converter, they are used to digitize the analog signal using the…

Q: A K-type thermocouple is used to measure the temperature of a system that is known to be 850 degrees…

A:

Q: (a) Figure Q2(a) shows a clipper circuit made with a germanium diode. Given the voltage input, Vin =…

A:

Q: down the equations of single Write phase transmen ot Bive the names of) he resistances, reae tance,…

A: A single-phase transformer operates only on one phase of electricity. From low voltage to high…

Q: Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm…

A: Given that: R=50 ΩC=40 μF  V= 180 volt Current I=3.13 A Find frequency f.

Q: 3.9. Suppose a drift current density of 5000 A/cm² ex- ists in the neutral region on the p-type side…

A: Note: Since you have posted multiple questions, As per the Bartleby guideline, I am solving Problem…

Q: Figure Q5(b) shows a 3.5 km long single phase distributor supplied two loads. The loads connected to…

A:

Q: solar cells short circuit current, Isc-5A and open circuit voltage, vo.c.-D0.6. * The power…

A: power of solar cell= P= Voc * Isc P= 0.6 * 5 P= 3 watt

Q: circuit shows such an arrangement for a small consumer electronics device powered by two AA…

A:

Q: A thermistor is placed in a 200°C environment and its resistance measured as 30000Q. The material…

A: Given values are -

Q: Consider an electronic device that monitors the temperature of exhaled air by a patient. The circuit…

A:

Q: How would you measure the unknown resistance (Rx) with the help of avoltage source, null detector…

A: Given components: A voltage source, a galvanometer, unknown resistors RX and resistors R1, R2, R3…

Q: For an RTD the relationship between resistance and temperature is a. proportional b. no relation c.…

A: Note :- We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: d) Assume a bridge excitation of 5.0 volts; determine the bridge deflection voltage per 500 kg…

A: Given, R = 120 Ω GF = 2.02  Aluminum Column, d = 15 cm Aluminum Constant, E = 6.89 × 1010 N/m2 Area…

Q: Please explain the difference (in assumptions and when you use them in practice) between the BIS,…

A: The BIS (Best Interest of Society), SPE (Social Planner's Efficiency), and WSE (Welfare-Social…

Q: 3. What are the advantages and disadvantages of a dual slope ADC?

A: Dual-slope type ADC: The integrator generates two independent ramps in a dual-slope type ADC, one…

Q: B A O CLK K1 K CLR CLR CLR B Mod 8 Mod 6 Mod 3 ) Mod 7

A: the counter in the given figure is: the options are: a) Mod 8 b) Mod 6 c) Mod 3 d) Mod 7

Q: 9. The time constant of the circuit shown in the figure below is A. 25 sec. B. 0 sec. C. 025 sec. D.…

A: Given data, Circuit diagram is given as, This is the series RC circuit,

Q: The forward characteristic of a diode is shown in Fig. Q3. Use the characteristic to determine (a)…

A:

Q: Q5. What is interface .Explain what is inertial delay. Your answer

A: To verify a design we write test bench to check that it meet specification. Verification can be done…

Q: An engineer spends about …………………….….. percent of his/her time writing.   Select one: a. 70 b. 10…

A: Solution: In every engineers engineering career, they spend much time on theoritical knowledge and…

Q: Post a response to the following discussion questions. The introductory course sessions have…

A: Solution of first subpart: It is asked to cite some sources of nonlinearities that arise in the…

Q: A PMMC instrument has internal resistance of 0.66 k2 and gives full scale deflection for 30 mA. The…

A:

Q: ) The equation above contains really only three variables in it: Id, Vd, and T. All the other terms…

A:

Q: show the deriviation of the eq and show the solution on how to come up to the final answer

A: It is given that:

Q: а. j -119

A:

Q: A J- type thermocouple is used to measure the temperature in a heating process. The length of the…

A:

Q: Q5/ What is static VAR Compensator? Draw its schematic diagram. What are the two tasks of Thyristor…

A:

Q: a) Find the value of K that yields max 20% overshoot... b) Peak time.. c) Setting time........ d)…

A: Please note that as multiple subparts are asked in the question, as per Bartleby guidelines, only…

Q: In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for…

A:

Q: Given the circuit diagram:       Derive the state equation      Map for the outputs      Derive…

A: Given the circuit, as shown below: We need to:  Derive the state equation   Map for the outputs…

Q: Q5 / The resistance of a platirum thermometer wire measured at 50C°, 200C° and 500C° is 14,20322 ,…

A:

Q: You have been asked to investigate the loading effects on an alternator supplying a load and also…

A: Consider the given circuit, Let the voltage across load is V1.

Q: Q5 Figure Q5 shows a Heating Room. There is a thermal system consisting of an electric heater in a…

A: From heater heat that enters to room is q1. The heat is transferred to surroundings is q2 & same…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.