Answered: Q5/ Write a NC Part program (G and M…

Q5/ Write a NC Part program (G and M )Code to cut the slot using an end mill. Assume suitable data for machining parameters 10 10 N 10 R 13 45 R 13 10 5 08 45 X X

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.3: Cnc Turning: Programming

Problem 7RQ: If a G1 code command is programmed partway through a machining operation, but no F-value is given in...

See similar textbooks

Similar questions

Write the G code and M code for the design attached. State also the meaning of the codes (as shown in attached picture). Thank you. The parameters are given as follows: Spindle speed = 1800 rpmFeed=3mm/minDoc=0.05mmUNIT = mm
If a G1 code command is programmed partway through a machining operation, but no F-value is given in that block, what feed rate will be used?
Write CNC turning program for following part. Take depth of cut as 1mm, Feed 0.15mm/rev, Absolute programming, Coolant is on during the machining.
Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS drill bit and T2 is a 0.5" tapping bit. The rest of the features are cut using a 0.75" HSS milling tool, T3. Feed rate and spindle speed are 10 ipm and 2000 rpm. The material is low- carbon steel. Part thickness is 0.5”. Use dotted lines two show the path of tools movements. Set up proper operation conditions as discussed in the class today.
Q1 In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance between the fixed center is (225+X)mm. The length of the slotted lever is (525+X)mm. Determine the ration of time of cutting stroke to time of return stroke. Also calculate the length of the stroke . Note where X is two digit number made from the last two digit of the registration number of the students For example if the reg. no. of the student is 11912081 then X=81 and crank length is 80+81=161mm Draw the neat and clean diagram with proper scale. Rough drawings will not be considered.
Questions ( what is the diflerence between three-anis milling machine ? and five - axis 2. Calculate, the ked rate for milling with four teeth D= 40 mm end núll and' cutting speced Ve = speed Vc = 80 feed tooth per vin Write the NC code for the side milling 3. with D=10 mm end mill threegh poínts 1. 6. 42 (00 20 controllable point of the end mill Fead rate for vertical movement F=2000 am Feed vate for cutling (horizantal movement) is caloulated fn questian2. min 7 42 PIPZ P3
4. Write an APT NC Part program (milling and drilling) for the following work part.The outline of the part shown in Figure is to be profile milled using a 30 mm diameter end mill cutter. The part is 15 mm thick. Use the lower left corner of the part as the origin in the x-y axis system. The two holes are already drilled to fix the work part in the machine (no need to include in program). Use absolute positioning. The program style should be similar to the explanation in PPT. The expected answers – 1. To define all the positions of holes, curves and lines. 2.Movement of cutter outside the work part. 3.Step by step movements for drilling.
Write a complete part program using canned cycles to produce the drilled hole, groove, and thread on the workpiece that is shown in figure with Fanue syntax. You may assume that the OD (Outside Diameter) and chamfer are already finished. Use the following parameters: Material: 1018 steel Tool: Ф0.25 HSS drill, T0101 60° carbide threading tool, T0202 0.125 carbide grooving tool, T0303 Cutting speed: 300 SFPM for carbide and 100 SFPM for HSS tools. Use constant surface speed where appropriate Feed: 0.005 IPR (except for thread)
2. Write a complete program to mill around the part. The endmill is .500 diameter, and you want to leave .010 stock for a finish pass. Enter a diameter offset number (Dn) command for tool DIAMETER Geometry of .520 for machining a roughing pass around part. And then define another pass around part using the same program coordinates but a different diameter offset number (Dn), and enter in the correct diameter offset value of .500 to machine part to the finish size. TOOL 1 has 0.520 in D21 and 0.500 in D01 Tool Speed (rpm) Feed (ipm) Operation Finish outside contour, x .50 deep Tooling 1 .5D endmill 1200 6. 25 R.25 2 PL. R .50 2.00 XO YO 4.0 SO. 1.0 SQ. 5 DA. EM 1.250- X-2.5 Y-2.0 START POINT
Q: Describe G03 used in a CNC milling machine G-code. Include the syntax of both versions and give a detailed example.
3- Write a complete CNC turning program to obtain the finished part from the raw material. R5.0 20.0 30.0 65.0 09
Elaborate the following terminology of drawing “SQ THD DIA 21X3 LH ?