Q5 The velocity distribution for flow over a plate is gives by u = 2y – y where u is the velocity in m/s at a distance y metres above the plate. Determine the velocity gradient and shear stress at the boundary and 1.5 m from it. Take dynamic viscosity of fluid as 0.9 N.s/m².

Q5 The velocity distribution for flow over a plate is gives by u = 2y – y where u is the velocity in m/s at a distance y metres above the plate. Determine the velocity gradient and shear stress at the boundary and 1.5 m from it. Take dynamic viscosity of fluid as 0.9 N.s/m².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1)The model of the torpedo (a military vehicle that goes very fast underwater) as placed in a tank…

A: To obtain the solution of the 1st part of the question, we will apply the Froude model law, which is…

Q: A film of liquid with kinematic viscosity and density p spreads over a flat horizontal surface due…

A: Given Data: Pressure Variation is hydrostatic in y-direction at x=0, h=ho Find: (a) show that…

Q: Two concentric cylinders of radii a and b respectively (a > b) have their common axis lying along…

A: In steady laminar flow, the fluid is expected to travel in a circular motion two concentric…

Q: 1. A unknown 30°C liquid (S.G. = 0.85) flows into a surface which creates shear stress of 0.20 N/m2…

Q: The velocity profile for the course of a Newtonian substance between two wide, parallel plates is…

Q: A fluid of viscosity μ flows in the horizontal cylinder (radius R) shown in the figure under a…

A: The viscosity of the flow is, The velocity at the porous region is, The radius of the porous region…

Q: As illustrated in the figure, two moving plates are pulled in opposite directions at velocities u₁…

Q: 2) A 1 in Dia x 3 in long mild steel hammer head is to be heat treated for surface hardening. If the…

Q: The flow of a particular fluid is described by a velocity field given a u = x²y v = x³ = xy² w = 0…

Q: The equation representing a Bingham plastic fluid is given as T= (dv/dy) μ x Ty T= μ/((dv/dy)+ Ty)…

Q: The velocity in a certain flow field is given by the equation below, V = (x² - y²)ī — 2xyj Show that…

Q: The flow of a particular fluid is described by a velocity field given as u = x²y v = x³ = xy² w = 0…

Q: The force per unit area.

A: Given; Flow between the plates is solely due to motion of the top plate.Top plate is sliding…

Q: The velocity profile of a viscous liquid flowing over a fixed plate is given by v=0.68y- y° (v is…

Q: ity in metre per ermine the shea

Q: Consider the flow of a fluid with viscosity μ through a circular pipe. The velocity profile is shown…

Q: Explain the fundamental reason for shear viscosity oxz bị along the x-axis with velocity v(z). How…

A: Shear viscosity's primary function is to oppose the flow of fluid from one layer to another.

Q: 4. The viscosity of incompressible viscous fluid is u = 0.96m Pa s. The velocity field is given by:…

A: Fluid is a substance that deform continuously under the action of shear stress no matter how small…

Q: A- Two large surfaces are 2.2 cm wide of infinite extent contains a fluid with an absolute viscosity…

A: Given data : width of infinite extension = 2.2 cm Absolute viscosity of the…

Q: Q6. Tangential laminar flow of a Newtonian fluid with constant density and viscosity is occurring…

Q: Consider a flat interface between two immiscible fluids as shown. The flow is parallel in the x –…

Q: a. Compute the flow rate of 20 °C air through a 0.35 m square edged orifice plate that is situated…

A: Given:Air temperature, T=20oCSide of square orifice plate, S=0.35 mInner pipe diameter, d=0.80 mThe…

Q: The velocity field is given as u=y-1 and v=y-2. The units of u and v are m/s and the units of x and…

A: a).

Q: A thin plate of very large area is placed in a gap of height h with oils of Example viscosities µ'…

Q: Question 1: The plate in side Figure rests on top of the thin film of water, which is at a…

Q: The continuity equation for the compressible fluid flowing through the pipe is p1A¡V1 = P2A2V2.…

A: Continuity equation for the compressible fluid is defined on the basis of the conservation of mass.

Q: Develop the expression to determine: the elevation of the oil-water surface (Yi) and the pressure…

A: The course through permeable limits is critical both in mechanical as well as biophysical streams.…

Q: the constants 1, m, and m

A: L , m , n are the constrains of above equations.

Q: A piston has a 6-inch diameter where a 6.008-inch bore vertical tube slides. The piston is 6 in.long…

Q: 28] The velocity distribution for an oil flow over a square flat plate of size 2 x 2 m is 1 given by…

Q: The Cauchy stress tensor for a (compressible) Newtonian fluid is given by S(x, t) = -p(x, t)I + X (V…

A: Write the Cauchy stress tensor for a compressible Newtonian fluid. Sx,t=-px,t∥+λ∇·vx,t∥+2μsym∇vx,t

Q: Consider a laminar flow between two large parallel plates placed h= 0.7 mm apart. The surface area…

A: Given Data Surface area of plate is : A=0.86 m2 Upper plate velocity is : U=0.34 m/s Fluid dynamic…

Q: Q1) When the force (P) applied to the plate shown in Fig.1 ,the velocity profile for a fluid is…

Q: The velocity distribution for the fluid flow between two fixed parallel plates, shown in the Fig.…

A: Givenuy=3Umax21-yh2 where y is in mUmax=4m/sh=5mm=0.005mμ=3×10-3 Ns/m2

Q: Question 1: The plate in side Figure rests on top of the thin film of water, which is at a…

Q: 2. Consider a flow with the velocity profile given by the equation below. The fluid surface is…

A: The free stream velocity is The shear stress is .The dynamic viscosity is The velocity profile is…

Q: Q: Consider fully developed laminar flow in the annular space formed by the two concentric cylinders…

A: The velocity profile is The outer radius is The inner radius is

Q: Consider a rapidly rotating (ie, in near geostrophic balance) Boussineq fluid on the f plane. A)…

A: Dependent upon the limitation on p communicated is the arrangement . It shows that the geostrophic…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Q5
| The velocity distribution for flow over a plate is gives by u = 2y – y² where u is
the velocity in m/s at a distance y metres above the plate. Determine the velocity gradient and shear
stress at the boundary and 1.5 m from it.
Take dynamic viscosity of fluid as 0.9 N.s/m².

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel ball with the density of 6324 kg/m and the radius of 0,48 cm was dropped into the oil whose viscosity was to be measured as is seen in the figure. When the ball attains a constant velocity, the distance that the ball travelled was measured as 97 cm within the time interval of 4 sec. Before the experiment, the mass of the 100 ml-oil was measured as 2,8 gr. According to the data given above, find; a) the density of the oil (in kg/m). (Please do not use any decimal digit.) Yanıt:
Please fastt
Q1) When the force (P) applied to the plate shown in Fig.1,the velocity profile for a fluid is confined under the plate is approximated by u = 12 y0.25 mm/s ,where y is in mm. Calculate the shear stress at y 16 mm. Take u = 0.8x10 N.s/m2. 16 mm Fig.1
B/ Two components of velocity in an incompressible fluid flow are given by v=z³y³ determine the third component. u= x² - y³ and Do the velocity field U = 5xi + (3y + ty2)j represent physically possible flow?
Consider the velocity field represented by V = K (yĩ + xk) Rotation about z-axis is
In three-dimensional fluid flow, the velocity component an u = * + y z, v = - (xy + yz + zx). Determine the %3D satisfy the continuity equation.
2. Dynamic viscosity of the fluid is u = 8.0×10² Pa · S , flow along the flat, the velocity gradient isdu dy 10³1/s shear stress is ( ). А, 0.1Pа В, 0.8Ра С, 80Ра D, 100Pa.
between two infinite surfaces with lateral cross-section It is coated with glycerin with an absolute viscosity of μ = 1.025 Ns / m2. This a cube parallel to two surfaces and with sides of c x c x c cm slides downwards. If the density of the cube is ρ = 254 kg / m3 then U Find the velocity (m / s). (g = 9.81 m / s2)
The velocity axis flow function of the ideal fluid for flow in the plane,It is given as (given equation in the picture). It shows the main interactions in units of x and y meters. a) Determine the velocity components of the flow and determine if flow is physically possible? b) Calculate the pressure difference between points A (2, 2) and B (3, 3). c) Calculate the unit width flow (q) passing between the points A (2, 2 ) and B (3, 3). (given equation in the picture). Thank you indeed.
Problem 1 – A laminar flow fluid of known density (ρ) and viscosity (μ) flows between twoparallel plates with different velocities in the same direction. The top plate has a velocity Utop inthe positive x direction. The bottom plate has a velocity Ubot in the positive x direction. The twoplates are a distance of “a” apart. There is a pressure gradient in the x direction ( ). Derivean expression of the velocity and shear stress profiles between the two plates
In mechanical fluid