Q48 A single cylinder four stroke diesel engine having a swept volume of8.50 Cm3 is tested at 300 rapeme When a braking torque of 50 N.m iseffective pressure ofapplied, analysis of an indicator diagram gives a meanlo bar. Calculate the brake power and mechanical efficiency of the engine.Answers [ bip=|1:57kW ; Ym =73a1%]t TrHhe

Answered: Image /qna-images/answer/207f40fc-c021-4d4f-805f-37d1327ea204.jpg

Q48 A single cylinder four stroke diesel engine having a swept volume of 8.50 Cm3 is tested at 300 ripime When a braking torque of 50 N.m is applied, analysis of an indicator diagram gives a mean effective pressure of lo bap. Calculate the brake Power and mechanical efficiency of the engine. Answers [ bip=k57kW ; Ym =73.1%]

Q48 A single cylinder four stroke diesel engine having a swept volume of 8.50 Cm3 is tested at 300 ripime When a braking torque of 50 N.m is applied, analysis of an indicator diagram gives a mean effective pressure of lo bap. Calculate the brake Power and mechanical efficiency of the engine. Answers [ bip=k57kW ; Ym =73.1%]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a sprak ignition engine the following readings were observed. cylinder diameter 10 cm, stroke length 10 cm and clearance gap between TDC and cylinder head is 10 mm. for such engine the compression ratio will be а. 11 O b. 10 c. 100 d. 110
18 The power output of a six cylinder four-stroke engine is absorbed by a water brake for which the law is WN/20000 where the brake load, W is in Newton and the speed, N is in rpm. The air consumption is measured by an air box with sharp edged orifice system. The following readings are obtained. Orifice diameter 30 mm Bore 100 mm Stroke 120 mm Brake load 560 N %3D C/H ratio by mass Coefficient of discharge Ambient pressure Pressure drop across orifice Time taken for 100 cc of fuel consumption Ambient temperature Fuel density 83/17 0.6 %3D 1 bar 14.5 cm of Hg 20 s 27 °C 831 kg/m³ Calculate (i) the brake power (ii) the torque (iii) the brake specific fuel consumption (iv) the percentage of excess air and (v) the volumetric efficiency
The brake thermal efficiency of a diesel engine is 30%. If air to fuel ratio by weight is 20 and calorific value of fuel is 41800 kJ/kg. Find brake niean effective press re at STP (15°C and 760 mm Hg).
QUESTION 2 A pressure-fed bearing has a joumal diameter of 55.00 mm with a umilateral tolerance of -0.05 mm. The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the bushmg is 55 mm. Its central annular groove is 5 mm wide and is fed by SAE 30 oil is 55°C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 10 EN. The sump ca dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the minimum film thickness and average temperature. Given the film temperature is 85° c Attach File Browse My Computer QUE STION 3
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque being correspondingly adjusted. The brake power (bp) measurements are the following:With all cylinders firing = 12.5 kWWith cylinder No. 1 cut off = 9 kWWith cylinder No. 2 cut off = 9.15 kWWith cylinder No. 3 cut off = 9.2 kWWith cylinder No. 2 cut off = 9.1 kWThe lower calorific (or heating value, LCVf) of the fuel is 44100 kJ/kg. The clearancevolume (Vcl) of one cylinder 70.0 x 103 mm3. Determine:(a) Indicated power (ip) of the engine under these conditions.(b) The indicated thermal efficiency (c) The relative efficiency of this engine. (d) Draw schametic diagram
Q108 The fallowing data refers to a test ona single cylinder four stroke oil engine Cylinder bore 220mm; stroke 360mm; area of indicator diagram 360mm length af diagram 40mm; indicator Spring rating =1.25 mm/bar; Speed 300 rev/min brake load 441-3N at o.9m radius; fuel consumption 3.8 Kg/hr} Calorific Value of fuel 43124 kj/kg ; Cooling water flow 3.8kg/hrjrise intemperature of coaling water 48K;and specific heat capacity of water 4.1868 Kj|Kg.K 340d.13biliN Calculate: @ the mechanical efficiency the indicated thermal efficiencyui a The heat balance sheet expressed as ki/min andas percentage of the heat supplied to the engine.
A four-stroke cycle engine have a brake mean effective pressure of 160 lb/in^2, a stroke of 6 inches, with bore of 5.5 inches. The engine runs at 3000rpm with 8 cylinders. Find the Brake Horsepower. *Show complete solution. Thank you.
A four-stroke SI engine 0.08 m bore (d), 0.10 m stroke (L), is tested at full throttle at constant speed. The fuel supply (m; ) is fixed at 0.0011333 kg/s and the spark plugs of the four cylinders are successively short circuited without change of speed, brake torque (4) being correspondingly adjusted. The brake power (bp) measurements are the following: With all cylinders firing With cylinder No. 1 cut off With cylinder No. 2 cut off With cylinder No. 3 cut off With cylinder No. 2 cut off = 9.1 kW 12.5 kW 9 kW 9.15 kW 9.2 kW The lower calorific (or heating value, LCV) of the fuel is 44100 kJ/kg. The clearance volume (Va) of one cylinder 70.0x10³ mm³. Determine: (a) Indicated power (ip) of the engine under these conditions. (b) The indicated thermal efficiency (Nind, th). (c) The relative efficiency (7el) of this engine.
Asap
A six-cylinder two-stroke automotive engine has been designed to provide a maximum brake torque of (3.30x10^2) Nm at rated engine speed of (5.000x10^3) rpm. The engine specifications are listed below: Bore and stroke (mm): (8.4000x10^1) x (9.2000x10^1) Compression ratio: 11.0: 1 Find its brake mean effective pressure (bmep). The answer should be in kPa with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer
> box 01 E what is minimum coefficient of stare friction hassary to keep Jkg box stationary on the slide given a = 10° ? んんんんん6ay $100
I need clear and correct answer please do fast