Q46. When the operating temperature of a machine exceeds its insulation temperature rating: (a) the machine efficiency improves (b) the machine speeds up (c) the life of the machine is reduced (d) the machine slows down (e) the insulation burns Q47. The cooling fans of a motor dissipate heat through: (a) Conduction (b) Natural Convection (c) Radiation (d) Forced Convection (e) All of the above Q48. Find the energy absorbed by a copper winding when the winding temperature increases from 298 K to 353 K. The mass of the winding is 150 kg and the specific heat capacity of copper is 385 J kg ¹°C ¹. (a) 3,002,000 J (b) 3,002,000 J (c) 3,176,250 J (d) 2,589,620 J (e) 2 664 520 I

Q46. When the operating temperature of a machine exceeds its insulation temperature rating: (a) the machine efficiency improves (b) the machine speeds up (c) the life of the machine is reduced (d) the machine slows down (e) the insulation burns Q47. The cooling fans of a motor dissipate heat through: (a) Conduction (b) Natural Convection (c) Radiation (d) Forced Convection (e) All of the above Q48. Find the energy absorbed by a copper winding when the winding temperature increases from 298 K to 353 K. The mass of the winding is 150 kg and the specific heat capacity of copper is 385 J kg ¹°C ¹. (a) 3,002,000 J (b) 3,002,000 J (c) 3,176,250 J (d) 2,589,620 J (e) 2 664 520 I

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

At its normal operating speed, an electric fan motor draws only 10.8% of the current it draws when it just begins to turn the fan blade. The fan is plugged into a 120.0-V socket. What back emf does the motor generate at its normal operating speed? i
The field coil of a D.C. motor is shunted by a 27002 arc-quenching resistor as shown below: a. Explain what happens in the circuit when the supply is switched off, b. Calculate the total current supplied to the circuit 0.3 seconds after switching on c. Calculate the peak voltage VAB at the instant the supply is switched off (assuming steady state conditions have been achieved before switching off) d. Calculate the time taken for the coil current to fall to 20% of its normal running value after the supply is switched off (assuming steady state conditions have been achieved before switching off) e. Explain the effects on the circuit if the arc quenching resistor was replaced with a 3000 resistor. A 8Ω Field Coil 2700 1.2H Vs = 315V B
4)
A wind turbine gives maximum output power of 1MW at a wind speed of 15m/s. Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 400square meters. b. The wind rotor swept area is 835 square meters. c. The wind rotor swept area is 700 square meters d. The wind rotor swept area is 638 square meters.
Answer all questions from this section. Use a fresh page for each question. Question B1 [15 pts] An universal motor is very similar to a DC series motor in construction, but it is modified slightly to allow the motor to operate properly on AC power. A washing machine is driven by an universal motor, which is powered by single-phase AC source having 110 Vac and 60 Hz. The armature winding of the motor has the resistance and inductance of 0.4 Q2 and 3 mH, respectively. The field winding of the motor has the resistance and inductance of 0.8 02 and 6 mH, respectively. When the washing machine operates at half load torque, the motor draws 10 Aac and runs at 1000 rpm. Calculate the input current and speed of the motor when the washing machine operates at full load torque. At half load torque, (i) Calculate impedance of the armature and field windings. [3 pts] (ii) Calculate the average electromotive force (emf) and average current in the armature. [4 pts] At full load torque. (iii) Determine…
Q4 An industrial motor is to be protected against overload. Its nameplate details are three-phase 3.3 kV, 500 kW, 75 % efficiency and 0.85 power factor. The motor can withstand 15% overload continuously. The time constant of heat withstand characteristic is 10 minutes. A thermal relay is connected across a C.T. of 120/1 ratio. The time constant of the relay is also 10 minutes. The range of settings is 70 % to 150 % of 1 A in steps of 5 %. Suggest the proper relay setting for this application.
A 690 V 10 pole 50 Hz DFIG has the parameters R1=R¹2=5 m2, x1=x'2= 50 m2 and the magnetizing reactance Xm=2 Q. The machine operates at 633.3333 rpm. If the injected voltage refereed to the stator is -30 V, calculate the reactive power in the stator.
q11,q12
from 4 to 7
Q2. Answer two branch only A) Draw the Full-wave rectifier ammeter circuit with Step up transformer? B)Draw the PMMC scheme showing the deflecting and controlling forces? C)Draw the current flowing left to right producing positive deflecting torque?
The resistance of the field coils with copper conductors of a dynamo is 120 ohms at 25°C. After working for six hours on full load, the resistance of the coil increases to 240 ohms. Calculate the mean temperature rise of the field coils. [Ans. 39.8°C)
6. In relation to a compound d.c machine, choose the right statement from the following (A) Both series and shunt field coils have comparable and number of turns and cross sectional areas. (B) Shunt field coil has fewer number of turns and large cross sectional area compared to series field coil. (C) Series field coil has fewer number of turns and large cross sectional area compared to shunt field coil. (D) None of (A), (B) and (C) are correct statement.