a.8.) A robot can use a back-pressure sensor to(a) measure the intensity of visible light.(b) regulate the torque produced by an electric drill.(c) determine the orientation of magnetic lines of flux.(d) regulate the output of an acoustic transducer.OIQUA OMA BOITZUODAa.9.) When you apply AF voltage to the plates of an electrostatic transducer, the electric field between theplates fluctuates in intensity, causing01 903 900 benud! 1joneupent oibus riw 16 limst amosa(a) a magnetic field that moves the coil, producing sound waves.(b) the capacitance to vary, thereby generating a phase shift. to assivab terw miw silimet emoce8(c) forces that move the flexible plate, producing sound waves.(d) the plates to charge and discharge, producing AF current.to becogmos al merayaa.10.) Which of the following devices is a form of RF transducer?(a) A small loop antenna(b) A back-pressure sensor(c) An elastomerfar al venibrantxe b (d) An epipolar navigation sensor

a.8) Back pressure sensor : Robotics engineers use back-pressure sensors mostly to limit the…

a.8.) A robot can use a back-pressure sensor to (a) measure the intensity of visible light. (b) regulate the torque produced by an electric drill. (c) determine the orientation of magnetic lines of flux. (d) regulate the output of an acoustic transducer. OIQUA OMA BOITEUC a.9.) When you apply AF voltage to the plates of an electrostatic transducer, the electric field between the plates fluctuates in intensity, causing joneupsit oibus reiw simal emosald (a) a magnetic field that moves the coil, producing sound waves. (b) the capacitance to vary, thereby generating a phase shift. to anivab terw miw sallimet emoceß (c) forces that move the flexible plate, producing sound waves. (d) the plates to charge and discharge, producing AF current. to becogmos al metaya a.10.) Which of the following devices is a form of RF transducer? (a) A small loop antenna (b) A back-pressure sensor si te lyeni (c) An elastomer txa b (d) An epipolar navigation sensor

a.8.) A robot can use a back-pressure sensor to (a) measure the intensity of visible light. (b) regulate the torque produced by an electric drill. (c) determine the orientation of magnetic lines of flux. (d) regulate the output of an acoustic transducer. OIQUA OMA BOITEUC a.9.) When you apply AF voltage to the plates of an electrostatic transducer, the electric field between the plates fluctuates in intensity, causing joneupsit oibus reiw simal emosald (a) a magnetic field that moves the coil, producing sound waves. (b) the capacitance to vary, thereby generating a phase shift. to anivab terw miw sallimet emoceß (c) forces that move the flexible plate, producing sound waves. (d) the plates to charge and discharge, producing AF current. to becogmos al metaya a.10.) Which of the following devices is a form of RF transducer? (a) A small loop antenna (b) A back-pressure sensor si te lyeni (c) An elastomer txa b (d) An epipolar navigation sensor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Choose the correct answer 1.A robot can use a back-pressure sensor to a.measure the intensity of visible light. b. regulate the torque produced by an electric drill. c. determine the orientation of magnetic lines of flux. d. regulate the output of an acoustic transducer. 2. When you apply AF voltage to the plates of an electrostatic transducer, the electric field between the plates fluctuates in intensity, causing a. a magnetic field that moves the coil, producing sound waves. b. the capacitance to vary, thereby generating a phase shift. c. forces that move the flexible plate, producing sound waves. d. the plates to charge and discharge, producing AF current. 3. Which of the following devices is a form of RF transducer? a. A small loop antenna b. A back-pressure sensor c. An elastomer d. An epipolar navigation sensor
Question (2) A controlled half-wave rectifier has a 240 V rms 60Hz ac source, The load a is R=30 Ohm resistor (a) Determine the delay angle such that the average load current is 2.5A (b) Determine the power absorbed by the load (c) Determine the power factor.
A single phase fully controlled rectifier has RL load. Write the following a) Draw its circuit diagram and waveform. b) Draw and explain its quadrant operation. c) Explain why the negative voltage appear across the load. d) Explain how the negative voltage can be removed. L
The brushes of DC machines are usually made of and are in the shape of rectangular block. Select one: O a. Carbon Graphite O b. Ceramic OC. Steel d. Phosphor
The purpose of a Yoke in a dc machine is to - a. collect the current b. provide protection c. increase output voltage d. convert induced voltage in to DC
A DC generator or AC generator with rectifier having the same output voltage produced, which is better? Explain in details.
Explain the difference between conductive and inductive compensation
A three-phase half wave-controlled rectifier circuit is shown in the figure. It is operated from 3- star connected, supply transformer with a line to line ac supply voltage of 440 volts rms at 50 Hz. The thyristor are triggered at a delay angle of a = 30°. Assume continuous ripple free current. The average output current (in A) is Ro Yo Во No T₂ + Voc ∙Iac Load
4. Explain the relationship between back emf E, terminal voltage V and coil voltage drop IR in DC motor and generator respectively. i. Describe how the field strength affect the performance of DC motor and generator. ii. Explain how an external resister changes the DC motor and generator performance.
Solve it fast fast plz
A JFET is a driven device .... ... Select one: a. none of the above b. both current and voltage C. current d. voltage
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w