A three-phase half wave-controlled rectifier circuit is shown in the figure. It is operated from 3-o star connected, supply transformer with a line to line ac supply voltage of 440 volts rms at 50 Hz. The thyristor are triggered at a delay angle of a = 30°. Assume continuous ripple free current. The average output current (in A) is

A three-phase half wave-controlled rectifier circuit is shown in the figure. It is operated from 3-o star connected, supply transformer with a line to line ac supply voltage of 440 volts rms at 50 Hz. The thyristor are triggered at a delay angle of a = 30°. Assume continuous ripple free current. The average output current (in A) is

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
i need the answer quickly
2. A full wave rectifier is using a center tapped step down transformer. The input to the primary of the transformer is 110 volts rms and the turns ratio of the transformer (N1:N2) is 5:1. Load resistance (RL) is 3,900 ohms. No capacitor is connected at the output of the rectifier. Determine the following. g. RMS voltage at the output of the rectifier (across RL) h. Average voltage at the output of the rectifier (across RL) i. Peak current at the load
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
I need the answer quickly
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
In a half wave rectifier, the input sine wave is 200sin200 nt Volts. If load resistance is of 1kohms, then the average DC power output of half wave rectifier is calculated as a. 6.25W b. 4.05W c. 3.25W d. 5.02W
I have one (1) AC source, four (4) diodes, and one (1) thyristor. In this case, I would like to obtain a full- controlled rectifier using these components; please describe the circuit?
N H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr 150usec and the source voltage Vs = 200V at frequency = 5 kHz. Calculate the average output voltage. IC L.C. the HoNo locor
A three phase half-wave controller rectifier is connected to a highly inductive load. Show the operational sequence for each thyristor, at a firing delay angle of 135° and plot the load voltage waveform. (Note: the waveform should be plotted on 3-phase waveform template)
A three-phase half wave control rectifier is operated from 3-phase source 230 V, 50 HZ (supply) with load resistance R = 10 22. An average output voltage of 50% of the maximum possible output voltage is required. Determine a) firing angle, b) average and rms value of load current, and c) the efficiency.
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current