Q4:5- Copy from source to destination O Fast operation Register MOV Data Transfer Instruction 16-bit Address O O O O

Q: General purpose register EAX contains internal code (hexadecimal): 00020FFF General purpose register…

A: we have an EAX register which can be represented as:-     AH AL The highlighted part comes…

Q: If R12 contains the value 0x4000 and register R8 contains the value 0x20, the effective address (EA)…

A: Correct Option:  CSummary: - Using LDR (Light Dependent Resistor) Concept and converting into Hexa…

Q: write assembly code (2 instructions) to increment location 322H (solution should not exceed two…

A: Answer: LDA 322H INR A

Q: What are the values of the EBX and EDX registers (decimal) after execution of the following…

A: mov edx, 256 -> edx= 256push edx -> edx is pushed on stackmov eax, -10 -> eax= -10push eax…

Q: The data bus, address bus, and control bus of the expansion bus should be briefly discussed

A: The most frequent form of the system bus is the data bus, which transports data from one component…

Q: Q4/ Design hardwired control unit to manage the following instruction format. 4-bit OpCode 3-bit…

A: Here we draw simple hardwired control unit for given instruction:…

Q: With 8085 Write initialization instructions for the 8259A Interrupt Controller to meet the following…

A: In the below code, the ICW1 (initialization command word 1) is set to 11B, which sets the controller…

Q: Arrange the Instruction fetch sequence

A: Increment PC by 1: The first step is to increment the program counter (PC) by 1. This is done to…

Q: 6. Comment on each snippet with what the snippet does. Assume that there is an array, int arr [6] =…

A: We need to comment on code snippet to find the outcome.

Q: The 8-bit data (operand) is added to the contents of the accumulator and the result is stored in the…

A: 2-What is the 8085 Assembly Language Instruction That do the following  The 8-bit data (operand) is…

Q: IN AL,83h instruction belongs to In-Direct I/O Port addressing. Select one: True False

A: here have to determine correct option for instruction belongs to In-Direct I/O Port addressing.

Q: draw the timing diagram of the following instructions MOV E,A

A:

Q: SBB instruction is arithmetic in type.

A: True   Sbb-arithmetic instruction-microprocessor, Assembly Language SBB: Subtract  with Borrow…

Q: Design a 512Gbyte memory if a memory chip of 8Gbyte was available ?

A: The memory is designed by the basic unit of memory cells. The memory cells have basic…

Q: Briefly explain or comment on the purpose of each line of code in SIC assembly code below

A: The code given in SIC Assembly language is: LDA FIVESTA ALPHA LDCH CHARZ ALPHA RESW 1FIVE WORD…

Q: With 8085 Write initialization instructions for the 8259A Interrupt Controller to meet the following…

A: The below code initializes the Interrupt Controller with the following specifications: Interrupt…

Q: (B) To select an address for a control memory of size (2048 words of 24 bits each), the size of…

A: we have 2 11 (2048)memory size i.e 11 bit addressing

Q: Suppose that BSR=05, TBLPTRL=04, TBLPTRH=05 FSR1L=04 FSR1H=04 Write one instruction that increments…

A: Dear Student,  FSR1 currently points to 404H to make it point to 405H  We need to increment FSR1.

Q: DEC instruction can decrement DS Register. Select one: O True O False

A: According to the information given:- We have to verify the mentioned statement is true or not

Q: Which of the following registers holds the information before it goes to the decoder? A control…

A: Registers holds the information before it goes to the decoder

Q: IS U. 3-bit register A 2 3 A Id clk O o 0 0 0 0 0 rst

A: Given is a 3 bit register using D flip flop The register is a positive edge triggered.  So whatever…

Q: Q:The registers that are essential in memory write and read operations (which of the following…

A: NOTE  :-  As per our guidelines we are supposed to answer  only one question. Kindly repost other…

Q: Assuming the instruction is 16 bits, what will be the content of location 405 after the execution of…

A: Let's analyze the instructions step by step:LDA 5: This instruction loads the value 5 into the…

Q: Explain the function of following Pins of 8086/8088 Microprocessor. INTA & INTR…

A: Lets see the solution.

Q: Select the specialized uses of the EFLAGS register. each flag is a single binary bit each flag…

A: Introduction: A processor register is a type of local storage area on a processor that stores data…

Q: The interrupt vector for INT 18 is located at the hex physical address: 00000 00004 O 00018 00048 O…

A: Explanation: The interrupt vector table holds 256 records, each holds 4 Bytes. The interrupt vector…

Q: Direct exchange of data between two memory locations is permitted by XCHG instruction. Select one: O…

A: 1) XCHG instruction exchanges the contents of the specified source and destination operands, which…

Q: What differentiates EDGE from other training software in terms of project creation is unknown.

A: Establishment: Simply explained, a process is a series of procedures that must be followed in order…

Q: te the VHDL instructions for re dr

A: Q

Q: Discuss the importance of shift and rotate operations in ALU instructions.

A: In computer design, shift and rotate operations are essential parts of the Arithmetic Logic Unit…

Q: If logical address is 215 and relocation register is 1215 then physical address will be: 1000 1430…

A: Question If logical address is 215 and relocation register is 1215 then physical address will be:

Q: With 8085 Write initialization instructions for the 8259A Interrupt Controller to meet the following…

A: The below code initializes the Interrupt Controller with the following specifications: Interrupt…

Q: Dsign 32 M *32 -bit memory using 32 M* 16 bit memory ICs .

A: Here in the given problem we have to design 32 M* 32 bit memory using 32 M* 16 bit memory ICs. So…

Q: SWAP is a/an......... instruction Ological O Jump and Call O 1/0 Odata transfer O arithmetic

A: A swap instruction exchanges a value in memory with a value of a register.…

Q: Explain Relative Addressing mode?

A: In computers, a program is a sequence of instructions. Whatever code in whatever language you write…