Q4: The shaft for a high speed rotating machine has a diameter of 200 mm. The absolute pressure within themachine is 3x10°Pa and the operating temperature is approximately 120 Cº. Design a suitable labyrinth seal tolimit the flow of air escaping from the machine to a chamber at an absolute pressure of 1.5 bar to 0.05 kg/s with8 fins?

Given Data Initial pressure is :P1=3×105 Pa Final pressure is : P2=1.5×105 Pa Diameter of shaft is…

Q4: The shaft for a high speed rotating machine has a diameter of 200 mm. The absolute pressure within the machine is 3x10'Pa and the operating temperature is approximately 120 C°. Design a suitable labyrinth seal to limit the flow of air escaping from the machine to a chamber at an absolute pressure of 1.5 bar to 0.05 kg/s with 8 fins?

Q4: The shaft for a high speed rotating machine has a diameter of 200 mm. The absolute pressure within the machine is 3x10'Pa and the operating temperature is approximately 120 C°. Design a suitable labyrinth seal to limit the flow of air escaping from the machine to a chamber at an absolute pressure of 1.5 bar to 0.05 kg/s with 8 fins?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The device shown in the fugure below is known as a venturi. In theis specific venturi the differential pressure between locations 1 and 2 is 5 psi and the diameter ratio is D2/D1 =0.35 if D2= 8inches find the air flow rate through the frictionless venturi
1. A sphere of radius a is moving with velocity U along the axis of a tube with circular cross-section of radius a(1 + €) with a closed end. See Figure 1. Determine the force exerted by the fluid on the sphere if the Reynolds number and e are small.
Problem 3: Leaking Tank Your engineering firm has been asked to determine whether the secondary clarifier (labeled "SECONDARY") downstream from the aeration basin (labeled "AERATION") is leaking at your local wastewater treatment plant. You conduct measurements over 45 minutes. During this time, you determine the average inflow rate Qin = 4.5 m³/min, the average outflow rate Qout = 4.0 m³/min, and the change in volume in the secondary clarifier is AV = 2.2 m³. You also determine that the fluid removed from the aeration basin is 90% water and 10% air by volume, since the fluid contains air bubbles. These bubbles rapidly dissipate in the secondary clarifier. PRETREATMENT OVERFLOW SECONDARY SLUDGE DIGESTION TRASH DRYER AERATION AIR PRIMARY DRY SLUDGE FINISHING ALICANTOY Is the secondary clarifier leaking, and if so, at what rate? [kg/min] SCUM METHANE
QUESTION 3 The refrigeration plant onboard a fishing vessel maintain minus 20 °C in a fish storage hatch at a design ambient air temperature of 33 °C. The plant which rejects condenser heat to sea water at +22°C operates at evaporating and condensing temperatures of minus 20 °C and 30 °C respectively. It is fitted with a 4- cylinder R134a compressor having a bore of 100 mm, stroke 150 mm and speed 1500 rpm. Given that the suction gas superheat is 10 °C, condensate sub cooling is 10°C, volumetric efficiency of compressor is 80 % and discharge gas temperature 65°C, determine the following: (a) Power consumption. (b) Isentropic efficiency. (c) Cooling capacity. (d) Carnot efficiency of the plant.
The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you charge the chamber to high pressure. The pressure is maintained until you pull the trigger at which point the water (? = 1000 kg/m3) is released at high velocity.You have charged your pressure chamber to an absolute pressure of P1 = 697500 Pascals, much higher than today's outside air pressure of 101300 Pascals. The pressure chamber is location at a height of y1 = 0.103 meters above the exit point. The exit point has a small opening with radius r = 0.0033 meters.Determine all the following:The velocity at which the water exits the Super Soaker: v2 = m/sThe mass flow rate through the exit: kg/secThe volume flow rate through the exit: m3/secNOTE: You may treat the water chamber as a "tank" and approximate the water velocity there to be zero.
3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet and c is the oil return port. It is already known that D=200 mm, d1=160 mm and d=40mm. The flow rate of the hydraulic pump is q=60L/ min. Calculation: the velocity of the piston when the pump only supplies oil to port a and the velocity of the piston when it supplies oil to port a and b at the same time. Figure 12
-
For the cart of figure, compute the force on the wheels caused by deflecting the jet and thecompression of the spring, if its stiffness is 1.6 kN/m.
12.5 The shaft for a high speed rotating machine has a diameter of 150 mm. The absolute pressure within the machine is 2.5×10ʻPa and the operating temperature is approximately 443 K. Design a suitable labyrinth seal to limit the flow of air escaping from the machine to a chamber at an absolute pressure of 2.2 bar to 0.03 kg/s.
A centrifugal pump is used to pump water between two reservoirs as shown in the bellow figure. The dimensions and minor loss coefficients are provided in the figure. The pump rotates at 1600 rpm, the water inters the impeller normal to the blades and exits at an angle of 45° from radial. The inlet radius is 5.5-in, at which the blade width is 7.09-in. The outlet radius is 8.66-in, at which the blade width is 6.7-in. The volume flow rate is 23-cfm. Assuming 100 percent efficiency, calculate the net head produced by this pump in cm of water column height, the required brake horsepower in W and calculate the pump capability to pump water to upper reservoir. Reservoir z3-2, = 22.0 ft (elevation difference) D = 1.20 in (pipe diameter) KL. entrance = 0.50 (pipe entrance) KL. valve I = 2.0 (valve 1) KL. valve 2 = 6.8 (valve 2) Reservoir Valve 2 KL elbow = 0.34 (each elbow-there are 3) KLe L = 124 ft (total pipe length) e =0.0011 in (pipe roughness) = 1.05 (pipe exit) exit Pump Valve 1
I need the answer as soon as possible
Problem 5 A square tube is open to air at atmospheric pressure on the top and capped with a porous membrane on the bottom. The tube cross section is L = 1 cm by L = 1 cm. The porous membrane contains 100 vertically oriented cylindrical pores of diameter d = 0.1 mm. Surface tension holds a column of water (o = 0.072 N/m) from falling through the membrane. The contact angle of water with the tube is 20°. The contact angle of water with the membrane pore walls is 180° (as shown) just before the water column spills through the membrane. The membrane is 0.01 mm thick, over which there is negligible hydrostatic pressure difference. a) Estimate the vertical capillary force by the tube on the water column. b) Estimate the vertical capillary force by a single membrane pore on the water column. c) Estimate the maximum water column height that the system can hold up. Air g Cross-section A-A Water Water Tube h Membrane Air Membrane