Answered: Q4) If the open cylindrical container…

Q4) If the open cylindrical container as shown in Fig.3 rotates at = 8 rad/s. determine the maximum and minimum pressure of the water acting on the bottom of the container. - 1m 1 m 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A pan of negligible mass is attached to two springs of normal lengths as 0.5m each and having stiffnesses k, = 250(N/m) and k2 = 500(N/m). If a 10kg box is dropped from a height of Im above the pan, 1 m 1 m ks=250N/m k=500N/m 1m determine the maximum vertical displacement d. and elongation of each spring (s1 and s2). wwwww
Ex. A pitot static probe is inserted into duct of air heating system parall to flow and the differential height of the water Colum is measured. The flow velocity and the pressure rise at the of the pitot -statics probe are to be determined For water p = 1000 kg/m3. for air p = 1.1 kg/m3 Air h-2.4 cm
4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
Sssoon
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°
The initial pressures at A and B are the same at 109 kPa. If the pressure at the liquid at A (SG1 = 2.65) is increased to 134 kPa while keeping the pressure at B constant, determine the new position (Ah, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.69 cm., and the inclination of the tube is 16° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places. SG B Air Yı Δh Ah Mercury
The initial pressures at A and B are the same at 105 kPa. If the pressure at the liquid at A (SG1 = 1.96) is increased to 132 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.58 cm., and the inclination of the tube is 11° with respect to the horizontal. Assume unit weight of air to be negligible. Round off to three decimal places.
n the crest gate on a dam shown in the figure, surface AB forms the arc of a circle of 6 m radius subtending 60° at the hinge. The gate is 8 m long with water surface at B. Compute the vertical component of the total pressure on AB. 6 m hinge 6 m' Unit weight of the liquid (y) Area of the liquid above the crest (A) Given length of the gate Vertical Hydrostatic Force (Fv) m kN m kN ***answer Hydrostatic Force Fv on the box below: Answer: 1059.438 The correct answer is: 355.75
the value of oil is - 0.8 asap 15 mins
Please answer with a complete solution. Thank you! The forces acting on a 1-ft length of a dam are shown. The upward ground reaction varies uniformly from an intensity of pA (lb/ft) at A to pB (lb/ft) at B. Determine pA and pB and also the horizontal resistance to sliding H.
Consider the pressurized horizontal pipe network consisting of three pipes arranged in series. The characteristics of each pipe are summarized in the table. The flow of water at Node A is Q = 5 cfs and the pressure head at Node A is yA = 200 feet. The temperature of the water is 60° F. a) Determine the friction head loss hfric in feet in Pipe 1. b) Determine the friction head loss hfric in feet in Pipe 2. c) Determine the friction head loss hfric in feet in Pipe 3. d) Determine the pressure head ys in feet at Node B. e) Determine the pressure head yc in feet at Node C. f) Determine the pressure head yo in feet at Node D. Flow Friction Pressure Diameter Length Friction (feet) (cfs) head Нead Pipe (inches) factor f Kpipe loss (feet) Node (feet) 1 16 500 0.011 5 A 200 2 12 1000 0.013 B 3 10 750 0.015 D Node Node Node Node A в D 5 cfs 5 cfs Pipe 1 Pipe 2 Pipe 3
Problem 4. The pipe bend is in a horizontal plane. Oil (s = 0.88) enters the bend with a velocity of 3.50 m/s and a pressure of 280 kPa. Neglecting any energy losses in the bend, find the forces required to hold the bend in place. d = 200 mm d = 80 mm 65°