Q4: Heat is generated in a long wire of radius ro at a constant rate of go per unit volume. The wire is covered with a plastic insulation layer. Express the heat flux boundary condition at the interface in terms of the heat generated.

Q4: Heat is generated in a long wire of radius ro at a constant rate of go per unit volume. The wire is covered with a plastic insulation layer. Express the heat flux boundary condition at the interface in terms of the heat generated.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Assume steady-state, one-dimensional heat conduction through the symmetric shape shown in Figure 1.Assuming that there is no internal heat generation, derive an expression for the thermal conductivity k(x) for these conditions: A(x) = (1 -x), T(x) = 300(1 - 2x -3x),and q = 6000 W, where A is in square meters, T in Kelvin’s, and x in meters. Consider x= 0 and 1.
A hot fluid (60° C) flows inside an copper tube with 1.7 cm OD and 1.5 cm ID. The inside of the pipe has a heat transfer coefficient of 130 W/m2-K. The tube is exposed to a room with air and surrounding walls of 23° C. The heat transfer coefficent between the outside of the walls and the room air is 15 W/m2 K. Draw an equivalent circuit diagram of the heat transfer, and quantify the resistance to heat flow by each of the two convective processes, conduction in the tube, and radiation between the outside of the tube and the room walls. Are any of the resistances negligible to the overall heat transfer, and if so, which ones?
4.) A 4m steel pipe (35 W m-°C external diameter of 30mm. A 10mm thick layer of insulation W m-°C coats this pipe and there is a temperature difference of 10C between the internal and external temperature. Solve for the rate of heat transfer has 20mm internal diameter and has an
Q. Steam in a heating system flows through tubes whose outer diameter is 5 cm and whose walls are maintained at a temperature of 130 °C. Circular aluminum alloy 2024-T6 fins k = 186 W/m.K of outer diameter 6 cm and constant thickness 1 mm are attached to the tube. The space between the fins is 3 mm, and thus there are 250 fins per length of the tube. Heat is transferred to the surrounding air at 25 °C, with a heat transfer coefficient of 40W/m².K. Determine: 1. The increase in heat transfer from the tube per meter of its length as result of adding fins. 2. The efficiency of the fins. 3. Temperature at mid-point of the fins. Note: Equations and any other data required can be taken from textbook/handbook. 130°C 25°C
Q3. A small electric heating application uses wire of 2 mm diameter with 0.8 mm thick insulation (k = 0.15 W/m°C). The heat transfer coefficient (ho) on the insulated surface is 31 W/m2°C. Determine the critical thickness of insulation in this case and the percentage change in the heat transfer rate if the critical thickness is used, assuming the temperature difference between the surfaces of the wire and surrounding air remains unchanged. - Wire Insulator air 12 0.8 mm
Derive the combined one-dimensional heat conduction equation.
1 . A long cylindrical shell outer radius R₂ = 2 cm is shown in cylindrical shell is temperature Ti=10 c° and outer wall at Constant temperature T₂ = 20 C° Calculate the temperature at r= 1.5 cm (Consider conduction only) Assumptions: system is Thermal in Given: The of inner and the figure. The radial + The differential The system is: J²T dr² r maintained at steady state conductivity, K = 22.5 w/mc, system follows Fourier's law of heat Heat loss in axial direction is negligible. JT dr radius Ri=1cm Length L=lom inner Wall Constant is maintained = 0 of is Ti RI R₂ constant. conduction. equation representing Tz
The temperature distribution in a certain plane wall is: T-Ty =C₁+Cx²+C₁x² Where TI and T2 are the temperatures on each side of the wall. If the thermal conductivity of the wall is constant and the wall thickness is L, derive an expression for the heat generation per unit volume as a function of x, the distance from the plane where T-T1. Let the heat- generation rate be 'q0 at x = 0
Solve this one correctly. Very very important for me.
For steady state heat conduction in a composite wall (As = 5 m², LA=1 cm and LB =2 cm) as shown in below figure. Calculate the total thermal resistance and the rate of heat transfer from the wall also find the temperatures Ts1, Ts2 and Tc To,z=200°C h₂=10W/m².K KA=0.1 W/m-K T5,1 HL-L₂ 17 Tc Too,2 = 40°C h₂-20W/m².K k=Q04 W/m-K
!