Q4 For the networks in Fig. 4, determine the current I, using branch-current analysis, and then find the voltage Vab . Then Find the meshcurrents and the voltage Vb for each network in Fig4. Use clockwisemesh currents. Compare between the two methods (branch- currentvs mesh).- E4 +R2V aba6 V 10 NR R3+E240V25 VEE, E, 60 V++Fig. 4

In branch current method we assume a voltage V at node connected to R3. Then we will apply KCL at…

Q4 For the networks in Fig. 4, determine the current I, using branch- current analysis, and then find the voltage Vob. Then Find the mesh currents and the voltage V, for each network in Fig4. Use clockwise mesh currents. Compare between the two methods (branch- current vs mesh). - E4 + R2 V ab 6V 10 2 R3 + E2 40V 25 VEE, E,60 V +

Q4 For the networks in Fig. 4, determine the current I, using branch- current analysis, and then find the voltage Vob. Then Find the mesh currents and the voltage V, for each network in Fig4. Use clockwise mesh currents. Compare between the two methods (branch- current vs mesh). - E4 + R2 V ab 6V 10 2 R3 + E2 40V 25 VEE, E,60 V +

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

0.5mA 1V 2kO Vx + 3k0 6V Vy 5kO Vz 6ko 1. Using nodal analysis, which of the following is the value of the known node voltage/s? 2. Find the value of the node voltages that will be used to solve for Vx in Volts. 3. Find the values of the mesh currents that will be used to solve for Vx, in milliamperes. Assume a clockwise direction for all mesh currents. 4. Compute for the voltage Vz in Volts.
Q1- For the circuit shown in figure 1 Calculate the value of 1₁,13,15,using Nodel or Mesh analysis or any role ?... Q2- For the circuit shown in figure 2 Calculate the value of ITOT & VRS?..... Figure 1 Figure 2 E₁ 60 v + 20 R1 4 k Ohm R2 16V 8kOhm R3 6 k Ohm 40 www 20 R4 4 k Ohm www 20 R5 2k Ohm R6 4 k Ohm R7 2k Ohm 20 .). E₂ 20 v R8 2k Ohm
3.-Calculate the electrical currents already indicated with their respective label in the circuit, that is, the currents in each branch 11= 12= 13= Note. The current 11 passes only through R1, and R3, 12 passes only through R4, and 13 passes through R2 and Rs. Draw the polarity to active, passive elements, nodes and meshes. R₁=2 Q ww V₁=10 V a V2=6 V ry R4=3 Q R3=4 Q R2=40 ww www b www V3=4 V R5=2 Q
a) calculate the resistance R12345 between points A and B when no voltage source is connected - calculate the resistance R34 between resistors R3 and R4: - calculate resistance R345 between resistors R5 and R34: calculate resistance R2345 between resistors R5 and R345 b) calculate the current IR5 through R5 so that the voltage source is connected. - calculate the current from the source:- calculate the current through the rice tower R 1:- calculate the current through the replacement resistor R2345:- calculate the voltage drop across R2:- calculates voltage drop over compensation resistance R345:-check that the resistors R2 and R345.- calculate the current through R34: c) calculate the voltage UR4 over R4 when the voltage source is connected - The resistors R3 and R4 are connected in series, ie they have the same current that passes through both resistors I34 but divides the voltage into two voltage drops UR3 and UR4.Calculate the voltage across R3:Check that resistors R3 and R4 are…
1. a. Find the Thevenin and Norton equivalent circuits looking into terminals a and b for the circuit shown below by finding Voc and isc. Then, Rt = Voc/isc. What is the current of the 29 resistor if a wire is connected between terminals a and b, i.e., the two terminals are short circuited? b. Find Rt in this circuit by zeroing the voltage and current sources (we can do this since both of them are independent sources). + ww 192 5 V 1A 2Ω a b
Vs V2 R. Rg R1 Ry For the above circuit V-8 Volts, V- =10 Volts, V, = 5 Volts, R,-3 Ohms. R, =7 Ohms, R.-5 Ohms, 14 Ohms, R. =8 Ohms, R. F4 Ohms, 9 Ohms. R, - 9 Ohms. , = 3 Ohms Use mesh anelysis by inspecrion to determine R,. of the resistance matrb. Round youranswerto the nearest two decimal places. For example, ifyour calculation Is 23.457 Ohms then enter 23.46 as your answer.
Q4:- Determine the total resistancecRe) and the voltagel V) from the circuit of Fig.C4) + VI - 122 lo2 423 122 30VT Rt 3452 122 Fig.c4)
3. Determine the value of R, in Fig. to resistance of 9 k2. establish total R-9in R12 kn
Q4:- Determine the total resistance(Re) and the voltagel V) from the circuit of Fig.C4) los2 + VI I - 122 423 122 30VT Rt /22 342 Fig.C4)
Solve in digital format step by step
Q1: For the parallel network find the unknown quantities: E, R1, and 13. 12.3 A I3 E R2 20 N R3 { 4N 10.8 A Q2: For the below network: a. Find the total resistance RT. b. Find the source current Is and currents 12, 13 and 15. c. Find voltages V2 and V4. d. Find the total power. R3 12 N 4Ω R4 E 14 V V2 R2 6N 12 Ω V4 Q3: For the given network, calculate the resistance R3 if the current through it is 2A. R120 120 VE | 2 A R,20 Ω R
Q): For the figure shown below, use nodal analysis to find the value of Vo 2Vx 2/k A IkQ Ika IkQ 2kA Q(2): Use voltage and current division , and resistance combination to find i, in thr circuit of Fir brlow