Answered: Q4) Find the Norton equivalent circuit…

Q4) Find the Norton equivalent circuit for the portions of the networks of Fig. 4 external to branch a-b. Then, find the power dissipated through 10002. 60 120 w 12 V 100 72 V 1202 Fie 4 2A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 11PP: In an R-L parallel circuit, ET=208 volts, R=2.4k, and XL=1.8k. Find IT.

See similar textbooks

Related questions

Q: using the below circuit; a) calculate Is using kirchoffs voltage law. b)calculate power…

A: PART (A) : The circuit is : Where, R1=1 kΩR2=2 kΩR3=2 kΩR4=1 kΩ

Q: ng the circuit analysis steps below:

A: The currents and voltages are simply calculated by applying KCL and KVL.

Q: Use node-voltage method to find ib for the circuit shown

Q: The network shown in Figure 2 contains two voltage sources, V₁ = 30/0° and V₂ = 20/0°. Using mesh…

A: An electric circuit having 2 voltage sources. Using mesh current analysis To find (a) The currents…

Q: Q1) For the circuit shown below 12 V1 4A R1 2kQ 5V R3 1k2 1 2A R2 3kQ a) Label the meshes: b)…

A: In this question , we will do mesh analysis...And find out mesh currents...

Q: For the figure below, use node analysis to determine the voltages across resistors R₁, R₂, R₁. Let…

A: here we have to find the voltage across the resistors R1 , R2 , R3 .

Q: Using Norton's theorem, find the current flowing through the resistor RL of the network in milli…

A: I HAVE EXPLAINED IN DETAIL

Q: V₁ R₁ R₂ = 2 V, R₂ R₂ Find Va and the power absorbed by the dependent voltage source in the circuit…

A: The question is about finding current and power in the given circuit.

Q: 3.-Calculate the electrical currents already indicated with their respective label in the circuit,…

Concept explainers

Thevenin Theorem

Any linear circuit, no matter how complex, maybe simplified to an equivalent circuit utilizing only a single voltage source and series resistance coupled to a load, according to Thevenin's Theorem. The superposition principle says that all foundational equations must be linear, and the notion of "linear" is still the same (i.e., there should not be any exponentials or roots). This is particularly the case when operating with passive elements like resistors, inductors, and capacitors. However, some components (particularly some gaseous and semiconductor devices like tunnel diode, Schottky diode, transistors like BJT, MOSFET) are nonlinear, meaning their current resistance fluctuates with voltage and current. As a result, circuits made up of these parts are known as nonlinear circuits.

Question

Q4) Find the Norton equivalent circuit for the portions of the networks of Fig. 4
external to branch a-b. Then, find the power dissipated through 10002.
60
w
120
ww
12 V
100
72 V
1202
Fig 4
2A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Knowing the resistance of the resistors and the EMF of the sources, find the currents in the branches.Proceed comparative analysiswith calculation (equations) and mathematical analysis (Ansys). Create reports with calculations (current on each elements, voltage on each elements), screenshot from Ansys and conclusion. my c variant is 2
Let the following electrical circuits be, in which it is required to determine the value of the voltage V shown:Note that the two previous circuits are identical, the only difference is the load element that has been selected in each of them: in electrical network 1 the load element is resistor R3 while in electrical network 2 the element of load is resistor R1.a) Find, using Thévenin's theorem, the voltage V in electrical network 1.b) Find, using Thévenin's theorem, the voltage V in the electrical network 2.
What is KCL at Node label V1,V2,V3,V4 and at supernode V3,V4
Using the Norton equivalent for the circuit determine its normal range of load current values.
Q3) Consider the following 230 V TNC network a) Is the RCD allowed to be used as protection device for this network? Why? b) Assume that the total RPEN = 22 and (each section RPEN1=RPEN2=RPEN3=RPEN4= 0,5 2). Find VFI, VF2, VF3 and VF4- c) Find whether a 20A gG fuse is a correct protection device for the network. d) Find whether a B32 A circuit breaker is a correct protection device for this network. RPENY M RPEN 3 M RPENZ PE REENA MM ML IVF3 VF2 Notice: The faults don't occure at the Same time, but Single.
1) A Wheatstone bridge has a strain gage in the lower right leg with a 100 ohm nominal resistance. It is mounted on steel with a Modulus of Elasticity (E) equal to 30x106 lb/in2. The other resistors are equal to 100 ohms. The bridge voltage is 5 V. a) What is the bridge output in V per 1250 lb/in2 of stress? Assume the Gage Factor = 2.0. b) What is the loading error produced by measuring the output with a voltmeter having an input impedance of 70 KΩ. c) If the bridge and the strain gage is used to measure the strain on a steel structure with a strain of 700 microstrain (u strain), what will be the bridge output in Volts?
Find VAD, VB and VCE
Several steps are required to find the thevenin voltage and resistance for a linear two-terminal circuit like that shown in Fig. (a). Identify whether each statement is true (Required) or False (not required) True or false
Determine the total uncertainty in the value found for a resistor measured using a bridge circuit for which the balance equation is X-SP/Q given that P = 10000 t0.05% Q = 100nt 0.05% S is a resistance box having four decades as follows: decade 1 of 10x10002 resistors, each ±0.52 decade 1 of 10x1002 resistors, each ±0.12 decade 3 of 10x102 resistors, each t0.050 decade 3 of 10x1Q resistors, each 10.050 At balance S was set to the value of 5436 Q.
For this circuit, find the Thevenin equivalent resistance RTH. RTH is found by using the test source method. Note for this circuit, the Thevenin voltage is zero since there is no independent source present. 1K b G CH 2K ohms 1 -V₁ Amps 500 1K ohm
Find the equivalent resistance Rab in the circuit shown below. 3302 50U2 Slou2 4002 322 20 U2 4002 b. www 3OU2 e
How many nodes are present in the circuit given below? Mark all the nodes, and identify theessential nodes and the non-essential nodes. Using only Ohm’s Law, KVL, and/or KCL (you cannot use theconcept of equivalent resistance) find the current through all elements in the circuit, find the voltage drops acrossall elements in the circuit, assign polarities to voltage drops across all circuit elements. Find all node voltages.Show that KVL holds true for the loop.