Q4) Determine whether the 90-kg man can move the uniform box has a mass 140-kg and show if the box will slip or tip. If the coefficient of static fraction between man' shoes and the floor is 0.5 and between the box and the floor is 0.2. Assume the man only exerts a horizontal force on the box.

Q4) Determine whether the 90-kg man can move the uniform box has a mass 140-kg and show if the box will slip or tip. If the coefficient of static fraction between man' shoes and the floor is 0.5 and between the box and the floor is 0.2. Assume the man only exerts a horizontal force on the box.

Name: Q4) Determine whether the 90-kg man can move the uniform box has a ma
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q4) Determine whether the 90-kg man can move the uniform box has a mass140-kgand show if the box will slip or tip. If the coefficient of static fraction between man'shoes and the floor is 0.5 and between the box and the floor is 0.2. Assume the mano

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 250 lb uniform crate (center of gravity at G) shown in the figure must be moved without tipping. The applied force P is horizontal. 1.5 ft 1.5 ft Determine: a. The largest coefficient of static friction between the crate and the floor that allows the crate to slide and 2.5 ft P. not tip 4.5 ft b. The corresponding magnitude of P 3.5 ft Include all needed FBD's to solve, and put units on your answers.
a 35 kg disk rests on an inclined surface for which m= 0.2 determine the maximum vertical force p that may be applied to bar AB without causing the disk to slip at c, neglect the mass of the bar
While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a horizontal 242-N force on the prybar as shown, what is the horizontal force exerted on rock C? Note that a small ledge on rock C supports a vertical force reaction there. Neglect friction at B. Complete solutions (a) including and (b) excluding the weight of the 17-kg prybar. 242 N A, 1750 mm 15 B 220 mm Answers: (a) Including weight, Fc = i N (a) Excluding weight, Fc = i N
The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is a 200-kg pebble in the bucket, with center of mass at G2 determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader. L0.5 m E 0.1 m_ D 0.2 m G2 0.18 m G1 0.6 m 0.5 m В 0.45 m 1.2 m 0.15 m 0.2 m 0.05 m Figure Q3
2. The two 200-lb blocks are pushed apart by the 15° wedge of negligible weight. The angle of static friction is 12° at ali contact surfaces. Determine the force P required to start the blocks moving. 1515 200 lb 200 lb
The uniform bar and the homogeneous cylinder each have a mass of 24 kg. The static coefficient of friction is μs at A, B, and C (the three points of contact). (a) Assuming equilibrium, calculate the normal and friction forces at A,B and C. (b) What is the smallest value of μs necessary for wquilibrium?
Each of the bodies shown is homogeneous and has a mass of 30 kg. Assume friction at all contact surfaces. Draw the fully dimensioned FBD for each body and determine the number of unknowns.
Determine the maximum downward force Pmax that can be applied to wedge A that will keep the assembly in equilibrium. Based on the value of the force in link BC, determine whether block C will slip or tip first. At Pmax, what are the frictional forces between wedge A and block B, fAB, and between wedge A and wall D, SAD? The weight of block C is 192 N while that of the wedge is negligible. Draw the FBDs of wedge A, block B, and block C. Label correctly all the forces (especially normal and frictional forces with proper subscripts) and indicate the direction of the impending motion next to each FBD. Note that the weight of block B, though not negligible, is not necessary in the computation. W HAD 0.27 D P A B 60° HAB= 0.14 |sg =0 E C 1 m HCF = 0.375 F R 2.4 m 3.2 m
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
1.2 m \30° 15 m Fig. P4.1
The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. P А 30° d = 0.40 B 2.2 d Answer: P = i mg
Problem 3 - Determine whether the block shown is in equilibrium. Find the magnitude and direction of the friction force. Ms=0.30 MK=0.20 400 N 300N 130 45°