Q4-A Design a special type of encoder which is shown in the following figure. This encoder works in such a manner where for each combination of inputs, 2 outputs are active high as shown in the mentioned truth table. Put down the Boolean expression for each output (D7, D6, D5,D4,D3,D2,D1DO) and sketch the logic gate matrix representation for the design. Do D, 2 l1 lo D7 D6 D5 D4 D3 D2 D1 Do 3to Decoder 0 0 0 1 00 0 0 0 1 0 1 0 0 0 1 1 0 0 0 De • D, 0 1 0 0 0 1 1 0 1 1 0 0 10 0 0 1 1 10 1 0 0 1 10 0 10 1 1 10 0 1 0 0 1 0 0 1 1 0 0

Q4-A Design a special type of encoder which is shown in the following figure. This encoder works in such a manner where for each combination of inputs, 2 outputs are active high as shown in the mentioned truth table. Put down the Boolean expression for each output (D7, D6, D5,D4,D3,D2,D1DO) and sketch the logic gate matrix representation for the design. Do D, 2 l1 lo D7 D6 D5 D4 D3 D2 D1 Do 3to Decoder 0 0 0 1 00 0 0 0 1 0 1 0 0 0 1 1 0 0 0 De • D, 0 1 0 0 0 1 1 0 1 1 0 0 10 0 0 1 1 10 1 0 0 1 10 0 10 1 1 10 0 1 0 0 1 0 0 1 1 0 0

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

THIS IS LOGIC Design a 3-bit " 1’s complement circuit". Use A as input variable and Z for output NO NEED FOR SOLUTION, JUST LOGIC DESIGN AND EXPLANATION
Define BCD counter and it's applications. A circuit consist of five cascaded BCD counters.Find the range of counting of the cascaded sequence.
(a) A logic circuit shown in Figure Q.3 has a 4-bit input A and B, three 4-bit wide 2:1 muxes, a 4-bit adder, a 4-bit output F, and a carry flag C. For the given Table Q.3, fill in the value of output F and carry flag C for the given value of A, B, S0, S1 and S2. 51 52 1001 Flag C 0011 Figure Q.3 Table Q.3 A So S1 S2 F Flag C 0001 1000 0010 1001 1 1 0011 1101 0100 1101 1110 0111 1
Which of the following is an important feature of the sum-of-products form of expressions? • The delay times are greatly reduced over other forms. • The maximum number of gates that any signal must pass through is reduced by a factor of two. • No signal must pass through more than 2 gates (not including inverters). • All logic circuits are reduced to nothing more than simple AND and OR gates.
We want to perform subtraction operation in which we need a full subtractor. First draw Truth table for full subtractor. Due to pandemic you are unable to get the desire component. but you have only eight- to-one multiplexers with you. What do you think, can you still perform subtraction operation with multiplexer or not? If yes, draw the logic circuit.
Logic Design
1.) Discuss how to use K-map in logic circuit design and its purpose
None
Logic Circuits By using the 2 bit counter given in the picture as a package, design a 8 bit counter. Note: DO NOT COPY FROM OTHER WEBSITES
Using full adders in block diagram, other needed logic gates. Show the design of a circuit that performs A – B based on using 2's complement arithmetic where A and B are two unsigned 4-bit numbers. State the condition for error in your design.
Question 6a and b are: Draw the logic diagram for the following Boolean expression. Then simplify the Boolean expression in (a) using a karnaugh map. The picture goes into more details about the assignment.
Q = A +B as logic circuit using 4x1 Multiplexer below (with depicting the internal structures) draw that.