Q4- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in Fig. Determine the maximum permissible value of T if the 2T allowable torsional shear stresses for steel and aluminum are 100 MPa and 75 MPa respectively and the angle of rotation at A is limited to 3 degrees. The Shear Modulus, G-83GPa and Gal-28GPa. 150 mm Abby -225 mm- 175 mm Beel -300 mm - B.

Q4- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in Fig. Determine the maximum permissible value of T if the 2T allowable torsional shear stresses for steel and aluminum are 100 MPa and 75 MPa respectively and the angle of rotation at A is limited to 3 degrees. The Shear Modulus, G-83GPa and Gal-28GPa. 150 mm Abby -225 mm- 175 mm Beel -300 mm - B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.80 in., a length of L1 = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.3 ksi. Brass segment (2) has an outside diameter of 0.60 in., a wall thickness of 0.05 in., a length of L2 = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.2 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.06 in., a length of L₂ = 24 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ (1) TB B L2 (2)
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 45 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.6 ksi. Brass segment (2) has an outside diameter of 0.80 in., a wall thickness of 0.14 in., a length of L2 = 32 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the loadP 20 KN is applied. 15m What is the axial deformation of stecl rod in mm?
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.90 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.6 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.06 in., a length of L2 = 20 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.4 ksi. Determine: (a) the allowable torque Tg that can be applied to the compound shaft at flange B (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque T.
An extruded aluminum beam has the cross section shown. The vertical shear in the beam is 145 kN. Assuming a=85 mm, b-87 mm, c=7 mm and d=15 mm, determine the shear stress at (a) a and at (b) b a a/2 -b- The centroidal moment of inertia is given as ]x10-6 (m4)
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
A 260 mm bar AB with a rectangular cross section of 17 x 30 mm, consists of two aluminium layers with cach being 6 mm thick and brazed to a centre steel layer of 5 mm thickness as shown in Figure Q3. An axial tensile force of P- 37 kN is applied to the assembly by means of a rigid end cap at B. Given that the assembly is fixed at end A and the Young's modulus of aluminium and steel are E.= 70 GPa, Es= 200 GPa, respectively, determine: i Whether this structural configuration is statically determinate or statically indeterminate, and clearly explain your reasoning. ii. The normal forces in the aluminium layers and the steel layer i. The normal stress in the aluminium layers and the steel layer. State whether the stresses are in tension or compression iv. Determine the deformation of the assembly Cross section of the bar 6 mm 5 mm 6 mm 30 mm 260 mun Aluminium. Steel- Aluminitum Nא 37 30 mm
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5