Q4) A 250 V, 4-pole series motor has a 2 circuit wave-wound winding with 105 slots, each containing 12 conductors. The gap flux per pole is 0.02 Wb when the motor is on full-load and taking a current of 45A. the armature and field resistance are 0.2 ohm and 0.1 ohm respectively and iron and friction losses total 700 W.calculate (1)speed (ii) shaft - torque and (ii) H.P.

Q4) A 250 V, 4-pole series motor has a 2 circuit wave-wound winding with 105 slots, each containing 12 conductors. The gap flux per pole is 0.02 Wb when the motor is on full-load and taking a current of 45A. the armature and field resistance are 0.2 ohm and 0.1 ohm respectively and iron and friction losses total 700 W.calculate (1)speed (ii) shaft - torque and (ii) H.P.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 3-phase, 115-V induction motor has the following constants: R1 = 0.070, R2' =0.08 N, X1=0.40 and X2' =0.20. At what values are for one phase the value of the gross power output?. only at which slip the gross power output will be maximum and
q1 a
Please question 4
A 460-V, 25-hp, 60-Hz, four pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R₁ = 0.641Ω R₂ = 0.3320 X₁ = 1.106Ω X₂ = 0.464Ω RM = 26.3Ω The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 % at the rated voltage and rated frequency, find the motor's a) Speed d) Pconv and Pout b) Stator current e) Tind and Tload c) Power factor f) Efficiency Activate
A repulsion start, induction run motor is used to drive a fan. The motor has a rated power of 2kW and operates at 220V. The repulsion start winding has a resistance of 0.5 ohm while the induction winding has a resistance of 0.3 ohm. Determine the total loss in the motor, assume 0.8 pf.
The bridged T netwook is opeoating în the steady state with v, -2cost: Deteimine a) ialt) b) i,lt) 2224H 2224 F
A large 3-phase, 4160 V, 60 Hz, squirrel-cage induction motor draws a current of 400 A and the total active power of 2500 kW when operating at full-load. The corresponding speed is accurately measured and is found to be 1178 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.15 0. The total iron losses are 26.5 kW and the windage and friction losses are 15 kW. Calculate the following: The power factor at full-load The active power supplied to the rotor The total I²R losses in the rotor The load mechanical power [kW], torque [kN.m], and efficiency [%] a. b. C. d.
A 400V, 25hp, 60HZ, 4 pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R1=0.6410, X1=1.106 Q, Rp=11.080, Xf=6.680 .The total rotational (windage and friction) losses are 1100 W and are assumed to be constant. The core loss is jumped in with the rotational losses. For a rotor slip of 3.2% at the rated voltage and rated frequency, the stator current is
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
A three-phase, two-pole, 35 hp, 480 V, 60 Hz, Y-connected induction motor has the following constants in ohms per phase referred to the stator: R = 0.322N R2 = 0.196 Q X1 = 0.6752 X2 = 0.510Q Xm = 12.52 The total rotational losses are 1850 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 3% at the rated voltage and rated frequency, determine the following: (a) The speed in rpm and in rad/s power factor (d) The developed power and output power (e) The developed torque and output torque (f) The efficiency. (b) The stator current (c) The
B3. A three-phase, 60 Hz 4-pole induction motor has a slip of 0.05 when the output is 30 kW. The frictional loss at shaft is 300 W. Calculate the following: (i) the rotor speed in r.p.m. (ii) the torque delivered by the rotor. (iii) the torque delivered to the rotor. (iv) the rotor IR loss.