Q4) A 230/460-V transformer has a primary resistance of 0.2 2 and reactance of 0.8 and the corresponding values for the secondary are 0.6 2 and 1.6 2 respectively. Q4.1) The transformation ratio of the transformer = Q4.2) The total resistance and reactance of the transformer referred to secondary side ohms and ohms respectively. Q4.3) The voltage drop in the transformer referred to secondary = Volts Q4.4) The secondary terminal voltage when supplying 12A at 0.8 p.f. lagging = = Volts

Q4) A 230/460-V transformer has a primary resistance of 0.2 2 and reactance of 0.8 and the corresponding values for the secondary are 0.6 2 and 1.6 2 respectively. Q4.1) The transformation ratio of the transformer = Q4.2) The total resistance and reactance of the transformer referred to secondary side ohms and ohms respectively. Q4.3) The voltage drop in the transformer referred to secondary = Volts Q4.4) The secondary terminal voltage when supplying 12A at 0.8 p.f. lagging = = Volts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A transformer having a nominal voltage = 399V and a no load voltage = 420V at its secondary, the short circuit current at the secondary of this transformer in function of its nominal current will be: Select one: Isc=10*In None of these Isc=30*In Isc=20*In Isc=40*In
The EMF equation of transformer referring to primary turns is Select one: O a. 4.440N,B O b. 4.440 fN. mi OC. 4.440 N,A O d. 4.440 fN,
Quiz2: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply 360 V to a load. a) Draw the circuit. b) What is the maximum load kVA that can be supplied? c) At the maximum load, determine ln, fy, and I,- d) What are the possibilities to connect it as a step-down autotransformer and determine the load voltage at cach case?
4.1 Assume that an ideal transformer is used to step down 13.8–2.4 kV and that it is fully loaded when it delivers 100KVA. Determine the following: (a) Its turns ratio. (b) The rated currents for each winding. (c) The load impedance, referred to the high-voltage side, corresponding to full load. (d) The load impedance referred the low-voltage side, corresponding to full load.
Regulation for the trans.
Write the voltage as a function of the transformer turns ratio for the following circuits respecting the dot polarity convention. N1:N2 V1
4.20 A 25-KVA, 2200/220-V, single-phase transformer has an equivalent series impedance of Zel = 3.5+ j4.0 referred to the primary side. The transformer is connected to a load whose power factor varies. The core loss is 160 W. a. Calculate the voltage regulation at full load, 0.8 PF lagging. b. Determine the highest value of voltage regulation for full-load output at rated secondary terminal voltage. c. Determine the efficiency when the transformer delivers full-load output at rated secondary voltage and 0.8 power factor lagging.
A transformer core is laminated in order to ....................................? (A) reduce hysteresis loss and eddy current loss (B) reduce only hysteresis loss (C) reduce copper loss (D) reduce all of the above losses (E) None of the above.
Complete the blank An isolating transformer is a (..........................)ratio transformer with several important applications.
If we increase the load than core loss and copper loss will... Decrease Increase Remain same
During the load test of single-phase transformer, when the secondary terminal voltage increases, the regulation of the transformer will ................?(complete)
- A Transformer has primary windings as Np = 750 and secondary windings as Ns = 125. Its secondary voltage is Vs = 36V and output power of the transformer is PN= 3200W. The value of loses powers are Pcu = 43W and Pfe = 29 W. The resistance of loads are RLI = 1,250 and R12 = 0,88Q. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit: Primary winding N, turns Secondary winding Ng turns Primary current Magnetic Flux, Secondary IsL s current ISL1 'Isl2 Primary voltage Secondary voltage RL1 R12 Transformer Core (a) the primary voltage Vr, (b) the secondary load currents ISLı and Isl2 if the transformer is rated at RLI and R12, (c) the resulting secondary power PSL, (d) the resulting primary power PPl, (e) the primary load current IPL, (f) efficiency nL