Q3/Draw the displacement and profile of a cam operating a knife-edge follower when the axis of the follower is not passing through the axis of cam shaft but in offset by 25 mm from the axis of the cam shaft las Follower to move outwards through 50 mm during 70" of cam rotation, (h) Follower dwell for the next 50. (c) Follower to return to its original position during next 90, (d) Follower to dwell for the rest of the cam rotation The displacement of the follower is to take place with uniform acceleration and uniform retardation during both the outward and the return strokes. The least radius of cam 50 mm

Q: A shaft rotating with 19 rev/s is uniformly accelerated at 0.4 rad/s? for 6 seconds. It then rotates…

A: Given, N1=19 rev/sα1=0.4 rad/s2t1=6 sect2=9 sect3=15 sec

Q: A Cam of base circle 60mm is to operate a follower of 25mm diameter. The follower has Simple…

A: Given , Speed of the cam , N =380 rpm Cam lift , h = 50 mm Angle of ascent , ϕa =120 * = 2π3…

Q: Consider a cam follower rising in harmonic motion to a lift of 210 mm as the cam rotates from 160 to…

A: Given   Lift, h = 210 mm  Angle = 190o Find   Displacement, y

Q: harmonic motion during 120º of cam rotation, (b) Follower to dwell for the next 60°, (c) Follower to…

A:

Q: Q6/ Draw the displacement diagram of a cam operating a knife-edge follower when the axis of the…

A: Given: Outward Stroke = 160° (uniform accelaeration)stroke = 50 mmdwell = 30°Return stroke =…

Q: A wheel rotating with 11 rev/s is uniformly accelerated at 0.3 rad/s2 for 8 seconds. It then rotates…

A: wheel roatation (N) = 11 rev/sec  uniform acceleration (α) = 0.3 rad/sec time (t) = 8 sec initial…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: below. The cam is rof nt P lying 5 mm away 5 20 mm The distance wost positions of the f

A:

Q: Use the following parameters for displacement diagram of a cam using the motions, Constant Velocity,…

A: It is asked to draw a displacement diagram based on the following  data Accent 60 Descent 60 dwell…

Q: maximum velocity of the follower

A: Given; Acc. to question,In a cam follower , the follower rises by h as the cam rotatesby δ…

Q: next

A: The shaft rotation is, (n)=10 rpm. The uniformly accelerated (α)= 0.3 rad/s2. The time required to…

Q: A shaft rotating with 10 rev/s is uniformly accelerated at 0.3 rad/s2 for 8 seconds. It then rotates…

A:

Q: 5. For the flat spring shown below (Ball feed device), with L = 65mm, t = 0.8 mm and b = 6 mm.…

A:

Q: QI/ (a) A car moving at a constant speed of 54 km/hr over a distance of 300 m. Calculate the time…

A: According to the details provided in the question,  we need to calculate parts a, b  and c  I am…

Q: m is to be designed for a knife-edge follower with the following data: m lift 50 mm during 100° of…

A:

Q: ith a minimum radius of 15 mm that rotates counter clockwise. The motion of the knife edge follower…

A:

Q: If the circular cam a has wa = 15 rad/sec clockwise, find the velocity of point B (in/sec) and the…

A: The given figure is re-represented with some other important points as shown in the below.From the…

Q: For a plate cam with translating offset follower with knife-edge similar to the following Figure,…

A:

Q: Please calculate the contact stress and contact force based on the below diagram and information.…

A:

Q: Given a circular cam and roller cam follower, determine the instantaneous displacement, velocity and…

A:

Q: b) Consider a cam follower falling in parabolic motion from lift of 264 mm as the cam rotates from…

A: Given   Lift, h = 264 mm  Angle = 200o Find   Displacement, y

Q: 21/ Draw the profile of a cam operating a knife-edge follower (when the axis of the follower passes…

A:

Q: Problem 3 (33) When the roller coaster is at point B as shown in the figure below it has a speed of…

A:

Q: Design a cam in non dimensional form consisting of 5 sections, each having the following…

A:

Q: 2- The swinging motion of the upper arm may be described as the follows; 0= 10 sin 0.06 t where 0 is…

A:

Q: roké of 20mm r (Omm r 00°. The maxin

A:

Q: 3: In the figure below, when an athlete is walking at a normal pace with, a = 10,8 m/sec ^2…

A: Draw the free-body diagram. Apply force equilibrium in vertical direction.…

Q: a) Consider a cam follower rising in parabolic motion to a lift of 218 mm as the cam rotates from 10…

A: Given   Lift, h = 218 mm  Angle = 70o Find   Displacement, y

Q: Compute the torque to be applied by the servo motor fixed to the pin at point

A: Torque applied by servo motor is required

Q: assume that the wedge makes a constant angle of ? = 19.0°. Suppose you want the wedge and the rod to…

A:

Q: A Cam of base circle 60mm is to operate a follower of 25mm diameter. The follower has Simple…

A: Let h=cam lift=50mm ω=angular velocity=39.79rad/s Φa =Angle of ascent=120°=2.09radian Φd=Angle of…

Q: Given the following data: Follower type roller follower, off-set to the right by 5mm; lift 30mm;…

A:

Q: (a) Design the profile of a cam (minimum radius of the cam is 1.5 cm) when the knife-edge follower…

A:

Q: Drawing the relationship between the linear displacement (x) and the angle (theta) in practice…

A: Deriving equations for displacement, velocity and acceleration of slider.

Q: 6.7 A plate cam with a reciprocating follower is to rotate clockwise at 400 rev/min. The follower is…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.