A cam has the following characteristics: (a) It starts from dwell and ends in another dwell (b) In section I the cam has a parabolic profile: Y = Ay² + By + C (c) In section I from 0 < y < 1/2 the cam rises to the height of ½ (d) In section II the cam has a cubic profile: Y = Dy3 + Ey2 + Fy + G (e) In section II from 1/2

Q: B D very sad kitty is trapped on a little platform connected to a gear system, the little scound…

A: The diameter are The angular speed of wheel A is  (clockwise)The distance between cat and cliff is

Q: 2- To balancing of rotation mass system of the same plane we need to addition two masses. * False…

A: AS PER COMPANY GUIDELINES, ONLY 1 QUESTION CAN BE SOLVED AT A POST. FOR SOLUTION OF OTHER QUESTIONS,…

Q: Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A…

A:

Q: Consider a cam follower rising in harmonic motion to a lift of 210 mm as the cam rotates from 160 to…

A: Given   Lift, h = 210 mm  Angle = 190o Find   Displacement, y

Q: Q6/ Draw the displacement diagram of a cam operating a knife-edge follower when the axis of the…

A: Given: Outward Stroke = 160° (uniform accelaeration)stroke = 50 mmdwell = 30°Return stroke =…

Q: A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and…

A:

Q: а. The cam angular velocity. b. The cam rotation segment widths, ß1 c. The lift (height) of the…

A:

Q: 3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet andc is the…

A: Given Data

Q: For the simple gear train below, Gear A is the input gear and rotates at 2500 rpm. The number of…

A: Given: Speed of gear A (nA)=2500rpmNumber of teeth in gear A (NA)=60Number of teeth in gear B…

Q: A pulley rotates about fixed axis. The relation between the angular displacement and time is e =…

A: There are three of Newton's equations of motion. These equations are the relation between various…

Q: In the figure shown, If vo=500 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A:

Q: acceleration of the follower rod A as a function of 0.

A:

Q: 1. Use the following parameters for displacement diagram of a cam using the motions, Constant…

A: Given dwell angle→θ=30° Accent angle→θa=60° Descent angle→θr=60° Lift or maximum height→h=6 Cm In…

Q: maximum velocity of the follower

A: Given; Acc. to question,In a cam follower , the follower rises by h as the cam rotatesby δ…

Q: next

A: The shaft rotation is, (n)=10 rpm. The uniformly accelerated (α)= 0.3 rad/s2. The time required to…

Q: A shaft rotating with 10 rev/s is uniformly accelerated at 0.3 rad/s2 for 8 seconds. It then rotates…

A:

Q: The rotor in the figure turning I and II formed in the beds imbalances and their angles are saving:…

A:

Q: At the instant under consideration, the hydraulic cylinder AB has a length L = 0.75 m, and this…

A: Write the relation in displacements in both sliders. xA2+yB2=L2

Q: Gear A of the winch turns gear B, raising the hook H. Gear A starts from rest at t=0 and its…

A:

Q: The velocity of the hanging block of the system shown in Figure 1 is y = 0.05cos20t downward. a.…

A:

Q: Q1) A cam rotating with a uniform speed are to give the roller follower of 20 mm diameter the…

A: Fig Space displacement

Q: ith a minimum radius of 15 mm that rotates counter clockwise. The motion of the knife edge follower…

A:

Q: If the circular cam a has wa = 15 rad/sec clockwise, find the velocity of point B (in/sec) and the…

A: The given figure is re-represented with some other important points as shown in the below.From the…

Q: The rod AC can move frictionlessly through the sleeve B. The sleeve C travels frictionlessly along…

A: Since the horizontal velocity vc remains constant, the acceleration of the system becomes zero.…

Q: Given a circular cam and roller cam follower, determine the instantaneous displacement, velocity and…

A:

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: b) Consider a cam follower falling in parabolic motion from lift of 264 mm as the cam rotates from…

A: Given   Lift, h = 264 mm  Angle = 200o Find   Displacement, y

Q: In the figure shown, If ve=500 mm/s, solve for the (a) velocity (in m/n) of D and (b) the angular…

A:

Q: 21/ Draw the profile of a cam operating a knife-edge follower (when the axis of the follower passes…

A:

Q: Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is…

A:

Q: In the figure shown, If v=700 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A:

Q: Problem 3 (33) When the roller coaster is at point B as shown in the figure below it has a speed of…

A:

Q: Design a cam in non dimensional form consisting of 5 sections, each having the following…

A:

Q: In the figure shown, If v=800 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular…

A:

Q: Problems: 2-1 For the figure shown, below, V = 2.5 n/s in the direction shown 1) Make scaled drawing…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.