Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the current wave form through the SCR for the input values of 5 V(45°), and 10 V(90°), and 8 V(135°). ▲ Vin RL R1 §2.2ΚΩ 7 520 ΚΩ T 1 Vin 1 I D 2π 90° 135° 2N3870 10 V 8 V 5 VT 71 - 45° Figure 3 T ~ R2 >2kQ DO

Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the current wave form through the SCR for the input values of 5 V(45°), and 10 V(90°), and 8 V(135°). ▲ Vin RL R1 §2.2ΚΩ 7 520 ΚΩ T 1 Vin 1 I D 2π 90° 135° 2N3870 10 V 8 V 5 VT 71 - 45° Figure 3 T ~ R2 >2kQ DO

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the output waveform and include the voltage value. +50 V 3.3 k -50 V R www Vout
Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the current wave form through the SCR for the input values of 5 V(45°), and 10 V(90°), and 8 V(135°). ▲ Vin RL 52.2ΚΩ R1 20kQ Vin D Σπ 2N3870 10 V 8 V 5 V -7 -r 1 70 I 90° 135° 45⁰ Figure 3 1 70 R2 2kQ DO
There is a small amount of current across the barrier of a reverse-biased diode. This current is called
C. The barrier potential for the diode in Figure 10 is 0.7 V. Determine the output voltage and the current in the diode. +15 10 ΚΩ ID 1 20 ΚΩ Figure 10 - Vo • 20 ΚΩ
Exam: Find the output waveform for the following full wave rectifier and the current pass through R1? 1:4 Di Voi= 0.7v 25v-- RL= 10kn %3! Dz Vo=0.7v D2
Draw outputwaveform vo diode is ideal.
Calculate the dc and ac components of the output signal across load RL in the circuit of Figure * Va = 150 V V, (ms) = 15 V V's V', (ms) R 500 2 Full-wave rectifier C, 15 μF C2 10µF RL 5 ka O vdc= 136.4V, Vac= 3.9V O Vdc= 163.4V, Vac= 9.3V Vdc= 13.4V, Vac= 9.9V O None of the above
The greatest advantage of TWT wave tube over Klystron tube Higher bandwidth Higher gain Higher frequency Higher Output
Please draw the input and out waveform. V-in = +10 to -10 peak to peak voltage.
Figure 4 b) Figure 5 shows the silicon base BJT with a Rc = 1 kQ, Rg = 10 k2, Vcc = 11 V, VBB = 6 V, BDC = 99. Determine Ig, Ic, lE, VCE and VCB- Rc 1 ko Vc 10 kn 11 V VBB 6 V Figure 5
For the following circuit choose the correct output if the diodes are ideal 1.0k +10V 5V 5 V -10 V +8.95 V 0. +5 V- at V 0 5 V -18 V Vout output +5.7 V-- -5.7 V-- Output O
Find the load voltage VaL if all Zener diodes are Si with Vz = 5 v. O zero O 5.7 V O 1.4 V O 6.39 V O 10 V R, = 10 ka R - 4.7 ko 20 V