2. Transistor in Saturation1. Connect the circuit as shown in Figure 1.2. Connect the base terminal to ground (0V).3. Record the base current, collector current and collector-emitter voltage.4. Apply 5V dc to the base terminal.5. Record the base current, collector current and collector-emitter voltage.TableVBBIBVBEIçVCECommentsOV+5V Vcc+ 5 VRCLEDRgB2N22225V, 1kHzSquare waveFigure 1

Given circuit is shown in below figure. When base is connected to ground

2. Transistor in Saturation 1. Connect the circuit as shown in Figure 1. 2. Connect the base terminal to ground (0V). 3. Record the base current, collector current and collector-emitter volt 4. Apply 5V dc to the base terminal.

2. Transistor in Saturation 1. Connect the circuit as shown in Figure 1. 2. Connect the base terminal to ground (0V). 3. Record the base current, collector current and collector-emitter volt 4. Apply 5V dc to the base terminal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

17)The region in the drain characteristics of FET where the drain current (ID) is linear to the drain voltage (VDS) is saturation region breakdown region breakdown region ohmic region
Question 2 (a) To achieve correct operation when using a Bipolar Transistor how should the two p-n junctions be biased?
Electronics Circuit: BJT biasing .A Voltage Divider bias NPN BJT (Beta = 80) circuit is connected to a 16VDC supply with the following components R1= 62 KOhms, R2= 9.1 KOhms, Rc= 3.9 KOhms, and Re= 0.68 KOhms. Determine the Emitter Voltage (Ve). a. 1.16 Volts b. 1.86 Volts c. 9.33 Volts d. 8.17 Volts
Q6) d) Show by means of a diagram how you will normally connect external batteries ini. PNP transistorii. NPN transistore) Describe how a semiconductor will behave at absolute zero temperature.
In normal operation, the junctions of an n-p-n transistor are: a. base-emitter forward biased and base-collector reverse biased b. both reverse biased c. both forward biased d. base-collector forward biased and base-emitter reverse biased The current flow across the base-emitter junction of an n-p-n transistor consists of a. equal numbers of holes and electrons b. the leakage current c. mainly electrons d. mainly holes
Consider the BJT circuit in Figure 6. Assume that the following values remain constant during the operating conditions, DC  = 100 and VBE = 0.65V,Calculate:i. Base, collector and emitter currents ii. VCE and VCB iii. DC alpha, DC
with the aid of a diagram describe a simple common emitter circuit with npn bipolar transitor and discus the relationship between base emitter voltage and base current
Select a region in which the collector current changes with respect to collector to emitter voltage, in IGBT characteristics. O a. Saturation region O b. ohmic region O c. Active region O d. Cut-off region
In the common emitter configuration the base emitter junction and collector emitter junction are a. forward bias and forward bias b. reverse bias and reverse bias c. reverse bias and forward bias d. forward bias and reverse bias
In a properly Biased NPN transistor most of the electrons from the emitter A. recombine with holes in the base, B. recombine in the emitter its self, C. pass through the base to the collector, D. are stopped by the junction barrier. In transistor, the relation among emitter current, base current and Collector Current is: A. Ic=IB+IE, B. Ig=IB+Ic, C. IE=Ic-IB, D. I=Ig-Ic. • Transistor is known as bipolar transistor because it has: A. Electrons, В. Holes, C. Electrons and holes, D. None of the above. In NPN or PNP transistor: A. Ic> IE, B. IE >Ic, C. IE = Ic, D. None of the above. The base of an NPN transistor is: A. Heavily doped, B. Lightly doped, C. Medium Doped, D. Doped by pentavalent material. In a transistor the value of a (B) is 100, the value of (a) is: A. 0.01, В. О.1, C. 0.99, D.1.
In both the npn and pnp transistors, correct biasing is considered to be: O a. Positive voltage being applied to the collector of a pnp transistor Ob. BC junction forward biased and BE reverse biased O c. BC junction reverse biased and BE forward biased d. Negative voltae being applied to the collector of an non transistor
How does the construction of a transistor differ from the construction of a PN junction diode? What are the two types of transistors? What are the three parts of a transistor called? Draw and label the schematic symbols for an NPN and a PNP transistor. What are transistors used for? How are transistors classified? What symbols are used to identify transistors? What purposes does the packaging of a transistor serve? How are transistor packages labeled? What are the basic functions of a transistor? What is the proper method for biasing a transistor? What is the difference between biasing an NPN and a PNP transistor? What is the barrier voltage for a germanium and a silicon transistor? What is the difference between the collector-base junction and the emitter- base junction bias voltages? What may cause a transistor to fail? What are two methods of testing a transistor? When using an ohmmeter, what should the results be for an NPN transistor? What are the two…