Q3.Load B is connected to adouble pulley by one of the two inextensible cables shown. The motion of the pulley is controlled by cable C, which has aconstant acceleration of 9 in/s, and an initial velocity of 12 in/s, both direction to the right. Determine (a) the number of revolutions executed by the pulley in 2 s, (b) the velocity and change in position of the load B after 2 s ,and (c) the acceleration of point D on the rim of the inner pulley at t=0. (5 degrees) D]

Q3.Load B is connected to adouble pulley by one of the two inextensible cables shown. The motion of the pulley is controlled by cable C, which has aconstant acceleration of 9 in/s, and an initial velocity of 12 in/s, both direction to the right. Determine (a) the number of revolutions executed by the pulley in 2 s, (b) the velocity and change in position of the load B after 2 s ,and (c) the acceleration of point D on the rim of the inner pulley at t=0. (5 degrees) D]

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Please answer question 2
PRINTER VERSION BACK NEXT Chapter 10, Problem 051 GO In the figure, block 1 has mass m, - 488 g, block 2 has mass m, = 551 g, and the pulley is on a frictionless horizontal axle and has radius R = 4.78 cm. When released from rest, block 2 falls 71 9 cm in 5 27 s without the cord slipping on the pulley. (a) What is the magnitude of the acceleration of the blocks? What are (b) tension T, (the tension force on the block 2) and (c) tension T, (the tension force on the block 1)? (d) What is the magnitude of the pulley's angular acceleration? (e) What is its rotational inertia? Caution: Try to avoid rounding off answers along the way to the solution. Use g = 9.81 m/s. m2 (a) Number Units (b) Number Units (c) Number Units (d) Number Units (e) Number Units
When a fan is turned off, its angular speed decreases from 168 rpm to 64.0 rpm in 6.08 s. A) what is the angukar acceleration of the fan? B) How fast the edges of the blades are moving (in m/s) at time 6.08 s, if they are 86.0 cm long?
Jinkee and Mommy D were riding on a carousel. Jinkee is further away from the axis of rotation than Mommy D. Which of the following statement(s) is/are true? i. They both have same linear velocity. ii. Mommy D has a lesser linear velocity than Jinkee. iii. They both have same angular velocity. iv. Jinkee has a greater angular velocity than Mommy D. A i and iv B) i and iii c) ii and iv (D) ii and iii
a. How fast in revolutions per minute must a centrifuge rotate if a particle 7.0 cm from the axis of rotation is to experience an acceleration of 100000 g's? b. Moment of inertia of a long (one-dimensional) uniform rod of mass M and length L2 through the center of the rod is equal to :a. 1/3 ML2 b. 1/6 ML2 c. 3/8 ML2 d. 2/5 ML2 e. 1/12 ML2
Ventilation fan in a house, the length of each blade is 0.25 m, rotating at a constant angle of 20 rpm, the tangential velocity of the outer end of one blade, and its tangential acceleration respectively is equal to: Choose and solve steps a- 0.2m/s , 2m/s2 b- 5.0m/s ,2m/s2 c- 0.52m/s , 0m/s2 d- 20m/s ,0m/s
6. A centrifuge in a lab rotates at an angular speed of 6500 rev/min. When switched off it rotates through 60 revolutions before coming to a rest. Find the constant angular acceleration of the centrifuge in rad/s².
In the figure below, block 1 has mass m1, block 2 has mass m2 and the shape pulley cylindrical, which is mounted on an axis perpendicular to the plane of the paper with friction negligible, has mass M and radius R. . When the system is released from rest, block 1 falls without the rope slipping on the pulley edge. From this, determine the magnitude of the acceleration of the blocks.
The shaft of an elevator motor turns clockwise at 180 rpm for 10 s, is at rest for 15 s, then turns counterclockwise at 240 rpm for 12.5 s. What is the angular displacement of the shaft during this motion? Draw angular position and angular velocity graphs for the shaft’s motion
A weight is tied to a rope that is wrapped around a pulley. The pulley is initially rotating counterclockwise and is pulling the weight up. The tension in the rope creates a torque on the pulley that opposes this rotation. a) On the axes below, draw a graph of the angular velocity versus time for the period from the initial instant shown until the weight comes back down to the same height. Take the initial angular velocity as positive. b) Draw a graph of the angular acceleration versus time for the same time period.
V = 4 m/s ac µ = 0.1 Center of rotation R = 20 m Car around corner A 400 kg car is going around a curb as shown. The radius of the turn is 20 m and the car has a velocity of 4 m/s. The coefficient of friction between the tires and the road is 0.1 a. What is the angular velocity of the car? a. Will the car make the turn?
ENGINEERING QUESTION- SOLVE FROM SCRATCH!An engine fan initially rotates at 450 rpm and is turned off for 20.0 seconds, during which time it rotates at 100 revolutions.a) How fast is the steering wheel turning when it turns again?b) In how much time after the first lapse would it have stopped completely?