Q3). The following data were recorded in a field. Draw contour lines of 152m, and 154m by interpolation method with scale 1:250. All dimension and readings are in meter. station BS BM 2.450 1 3 4 5 6 7 S 9 10 11 12 13 14 15 16 BM IS 0640 1.050 1.140 2.000 3.950 2.900 2.450 0.000 0.140 2.300 3.340 4.800 3.340 2.890 0.690 0.200 FS Remark RL =150m 2.450 2 3 4 7 6 5 9 10 11 12 -10 16 15 14 13

Q3). The following data were recorded in a field. Draw contour lines of 152m, and 154m by interpolation method with scale 1:250. All dimension and readings are in meter. station BS BM 2.450 1 3 4 5 6 7 S 9 10 11 12 13 14 15 16 BM IS 0640 1.050 1.140 2.000 3.950 2.900 2.450 0.000 0.140 2.300 3.340 4.800 3.340 2.890 0.690 0.200 FS Remark RL =150m 2.450 2 3 4 7 6 5 9 10 11 12 -10 16 15 14 13

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

42. A 30-m steel tape is used to measure the distance of a line. The measured distance is 457.65 m. After the tape was calibrated, it was found that it is 16 mm too short. What is the correct length of the line? +8 8 A. 457.406 m C. 457.921 m D. 457.125 m B. 457.894 m
Are the answers in #1 to #8 is correct? What are the correct answers?
23. If the surveyor is at Point A, and recorded the location of Line AB to be 200 degrees 35 minutes in WCB. The surveyor then recorded the location of Line AC to be 280 degrees 15 minutes in WCB. The length of AB is 530.68 meters and Length of AC is 275.45 meters. What is the length of the third line, Line BC?
Surveying: Measurement of Horizontal Distances
Q1) Draw contour lines of 301.2m, 301.6m, 302m, and 302.4m by interpolation method, with scale 1:200. RLs shown in the table below. All dimension and RLS are in meter. Station 1 2 3 6 7 S 0 10 11 12 13 14 15 16 17 18 19 20 21 24 25 RL 301 3 301 42 301 54 301.75 302 302.05/ 301.94 301.79 301.61 602 $1 301.74 301.68 301.78 301.96 302.16. 302.20 301.96 301 S1 301.63 301 51 301.50 301.77 302 01 302.21 302 38 15 16 25 14 124 13 18 23 301.542 12 22 5 m 10 11 20 21 5 m
COMPUTE THE OMMITED MESUREMENTS
Q.4. arithmetic check. Write your calculations in detail and fill the table. The units of readings in the table are meter (SI system). Please calculate elevations in the stations given in the table and show the Station BS FS H.I. Elevation ВМА 2.16 500.00 ТР 1 3.24 1.13 ТР 2 3.14 1.07 ТР 3 2.59 1.67 BM B 1.39
Activity 8 Answer this azimuth traverse problem. Provide a given, required, solution format and use a handwritten calculation. Draw a graph and write the directions. Simplify your answers.
Draw the profile for the point below: Distance (m) 0 22 30 45 Elevation (m) 355.7 355.4 354.2 353 60 78 85 91 125 150 352.6 352.9 353.4 353.7 354.7 355.2
1. Solve the traverse partitioning. Plot and label the traverse. Provide a step-by-step solution and a handwritten calculation. Attached above is the given and the sample problem.
Provide the detailed figure and complete solution. For all the computed values with decimals, use four (4) digits after the decimal.
Q2) Draw contours of 13m, 19m and 30m by interpolation method, with suitable scale. RLs at corners are shown on figure below. Recorded data are in meter. 22 13 7 25 19 14 31 28 23 5.00- 27 32 27 5.00