Q3. For the single-phase half-wave controlled rectifier with R-L load circuit shown below sketch io, Vo and determine the value of the firing angle (a) such that the average output voltage is 75V and find: a. The extinction angle (B) and conduction angle (8). b. The average current and RMS output voltage. a = ? io R = 50 2 Vs = 240V f= 60 Hz Vo 27T ot L = 200 mH

Q3. For the single-phase half-wave controlled rectifier with R-L load circuit shown below sketch io, Vo and determine the value of the firing angle (a) such that the average output voltage is 75V and find: a. The extinction angle (B) and conduction angle (8). b. The average current and RMS output voltage. a = ? io R = 50 2 Vs = 240V f= 60 Hz Vo 27T ot L = 200 mH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question-1: Consider the circuit in Figure below. 1. What type of circuit is this? 2. What is the total peak secondary voltage? B. Find the peak voltage across each half of the secondary. 4. Sketch the output voltage waveform across R1. 5. Sketch the voltage through D1? 6. What is the PIV for each diode? 120 V rms D2
a. With necessary diagrams explain the working of a reverse biased P-N Junction Diode.
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: DC output voltage b. Sketch the output waveform a. D2 D3 R1 = 12 k2 %3D DA Figure 2. Circuit for problem 5 and 6 ell ll
Please solve this question queckly
5. The bridge rectifier shown in Figure 2 uses ideal diodes. The input voltage is 24V. Find: a. DC output voltage b. Sketch the output waveform D2 D3 R1 = 12 k2 Da D Figure 2. Circuit for problem 5 and 6 6. If the bridge rectifier shown in Figure 2 is modified using silicon diodes, find: a. dc output voltage b. sketch the output waveform ell ll
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
2. A simple half wave rectifier consists of a diode and load. If the internal resistance of the diode is 1 ohm and the load resistance is 5 ohms. What will be the DC load current if the supply voltage is 12 Volts, draw the schematic diagram and also draw the waveform of the rectifier. 3. Determine the output voltage in the figure below Si Ge Vo R₁ 2kQ 20V R2 2kQ
Q3: The figure below includes a bridge full-wave rectifier circuit with a diode type is1N4007. The input voltage is Vin V2 120 sin 2n60t 5:1 D3 D1 120 V RL Vp(out) D2 DA 10 kN a) Draw the output voltage waveform for the circuit in the figure and include thevoltage values. b) What is the peak inverse voltage (PIV) across each diode? c) Determine the rms voltage, current and power delivered to RL d) Determine the average voltage, current, and power delivered to RL e) What is the ratio of Po(de) to Po(ac)? lll
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
Choices are: 45V 60V 10.09V 4.77V 30V 15V 9.55V 7.5V What id the right answer