Q3. Determine the allowable vertical load P that can be carried safely by the square pad foundation seen below. Factor of safety will be taken as 2. Unit weight of concrete is 24 kN/m. The column has a cross section of 400mm x 400mm. Use Terzaghi equation. silty clay 1m Y=16.7 kN/m3 0= 150 0.5m 0.80m GWT c=10kPa 2m clayey silt Y= 19.6 kN/m3 0= 250 4.0m

Q3. Determine the allowable vertical load P that can be carried safely by the square pad foundation seen below. Factor of safety will be taken as 2. Unit weight of concrete is 24 kN/m. The column has a cross section of 400mm x 400mm. Use Terzaghi equation. silty clay 1m Y=16.7 kN/m3 0= 150 0.5m 0.80m GWT c=10kPa 2m clayey silt Y= 19.6 kN/m3 0= 250 4.0m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a simply supported prestressed concrete beam, compute the stress in the top fiber at the centerline. Properties of the bearn are: Width of the bearm, b: 326 mm; Depth of the beam, d: 471 mm; Eccentricity of the beam, e: 157 mm; Prestressing Force, P: 739 KN; Superimposed Load, w: 6 KN/m; Length of the beam, L: 9 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) P. P.
The plan of a reinforced concrete column section, and the distribution of strains at the ultimate limit stage are shown below. The concrete is M20 grade and the steel of Fe 250 grade. Also sketched below, for convenience, are the concrete compression stress block and the design stress-
The subject is vibration engineering. please make the solution clean and understandable. thanks
The material used in the unreinforced expandedfoundation has poor tensile and flexural properties.To ensure that the foundation has sufficientrigidity, the most effective of the followingmeasures is ( )◼A. Adjust the average pressure on the bottom of thefoundation◼B. Control the allowable value of the height-to-widthratio of the foundation steps◼C. Improve the bearing capacity of the subgrade soil◼D. Increase the compressive strength of the material
Make a good quality solution
Hello and hope your help with foundation CEE 430 thanks
1. The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. The column is separated from the concrete foundation by a square bearing plate with the dimension of 160 mm x 160 mm. The working compressive and tensile stresses are 180 MPa and 200 MPa respectively, while the working bearing stress of concrete is 10 MPa. Find the largest force P that can be applied to the column. P Steel Concrete Foundation Bearing Plate
Q2: Compute the total stresses, which induced from geostatic stress and increase vertical stress from circular foundation under points A and B to 3 and 6 m depth from the base of the foundation. The foundation was constructed at 2.0 m below the natural ground level (NGL). The surface load intensity is 330 kN/m². R1= 4, (calculate R2 from the drawing, do not assume it). Assume any other parameter you need in your answer. Aqs net
Question :- The width of the beam is 250 mm and the overall deep 620 mm. It has three equal spans of 6.0 m each. The beam is arranged at 3.5 m from center to center, while the thickness of the slab is 200 mm. The imposed live load qk on the beam is 45 kN/m and the dead load gk inclusive of self-weight of the beam is 75 Kn/m. the characteristic strength of materials are feu = 30N/m², fy = 460N/mm² and f 250N/mm², Assume that the mild exposure for the beam and the nominal cover of 25 mm. Design the beam
2. Design a one-way slab to carry a service live load of 4000 Pa. The slab has a length of 4m with both ends continuous. Assume f'c = 21MPa and fy = 415 MPa for main bars and fy=276 MPa for temperature bars. Unit weight of concrete is 23.5 kN/m³.
A column 24 in. square, with f'c = 4ksi reinforced with 10 No. 10 bars, As=12.7 square inches. fy=50 ksi, supports a dead load of 276.06 kips and a live load of 175 kips. The soil (fill) has a unit weight of 100 pcf and the concrete unit weight is 150 pcf.The allowable soil pressure q(a)is 2500 lb/ft^2. Design a square footing with base 6 ft below grade, using f'c= 4 ksi and fy= 50ksi
Uniformity distributed load 100Kn/m² is carried by circular foundation. The diameter of Raft 10m. Determine the vertical stress below the centre of raft at the depth of 2.5m, 5m, 7.5m, 10m. Use Boussinesq eqaution. Please Show the all step.