Q3 // Two 300 mm x 16 mm plates are riveted together with 25 mm diameter rivets double cover butt joint as shown in figure below. Find the max. allowable force P. If you know the allowable stresses (shear stress of bolts=80 MPa, tensile stress of plate=160 Mpa and bearing stress = 160 MPa).'

Q3 // Two 300 mm x 16 mm plates are riveted together with 25 mm diameter rivets double cover butt joint as shown in figure below. Find the max. allowable force P. If you know the allowable stresses (shear stress of bolts=80 MPa, tensile stress of plate=160 Mpa and bearing stress = 160 MPa).'

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The lap joint shown is fastened by five % inch-diameter rivets. The bearing stress in the plates is…

Q: 4. Solve problem 8.10 in our textbook (find the safety factor for failure at the fillet). Note that…

Q: Solve the following problem of a steel tensile plate with a concentrated load applied at the top, as…

Q: Example: The coupling shown in Fig. below is constructed from steel of rectangular cross-section and…

A: For the given coupling P = 50 kN dia of bolt (d) = 15 mm To determine (i) the shear stress in…

Q: 03: For the cyclic stress shown in the figure (aside) calculate: 1. The mean stress 2. The range of…

Q: A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as…

Q: Problem 4-41: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of…

A: To findDetermine the magnitude of the largest elastic load P that can be applied to the…

Q: 5. Calculate the MS of the member below for tension in yield, if the material is Al 7075-T6 and the…

A: To calculate the margin of safety for a member for tension in yield with the material AI 7075-T 6.We…

Q: What will be the cross-sectional area in mm² of the prismatical bar of length 5 mm and weight per…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick. The…

A: Given Datat = 10mmσt = 60 mPaτ = 50 mPaσc = 80 mPaTo Find1) d2) P3) Pd4) n

Q: A long, flat steel bar 260mm wide and 35mm thick has a circular hole 50mm in diameter, centrally…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: 4. A double riveted lap joint with chain riveting is to be made for joining two plates 10 mm thick.…

Q: Figure 1: This bar is made of AISI 1020 cold-drawn steel and is loaded by the forces F=60 lb, F2= 80…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: A double riveted single cover butt joint (zig zag arrangement), is used for connecting two plates…

A: Given:- Permissible shearing stress in rivets = 120 MPa- Permissible tensile stress in plate = 150…

Q: A In Figure 2, different square cross-section bar with dimensions, loading condition and material…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: Problem 3 CD steel. Calculate the maximum principal stress within the rod. 100N The solid bent rod…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Question

Q3 // Two 300 mm x 16 mm plates
are riveted together with 25 mm
diameter rivets double cover butt
joint as shown in figure below. Find
the max. allowable force P. If you
know the allowable stresses (shear
stress of bolts=80 MPa, tensile
stress of plate=160 Mpa and bearing
stress = 160 MPa). *
300 m
pat
10 mm
16 mm
300 kN
100 kN
400 kN
Not of all above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N compressive load on the link. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
include FBD
A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?
Q-2 A portion of the stress–strain curve for a stainless steel alloy is shown in Figure Q-2. A 550 mm long bar is loaded in tension until it elongates 4.4 mm, and then the load is removed. (a) Determine the permanent set in the bar. (b) Determine the length of the unloaded bar. (c) If the bar is reloaded, determine the proportional limit. [Use the figure to make necessary drawings/markings to show your solution strategy!
Please do it typed not handwriting. Make sure the answer is correct Don't copy from any other online answers please
Just Solve a Use Abaqus
For the joint shown in the figure, if F = 28 kN and dn = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm 7.5 mm - de - F 18 mm - F 18 mm 125 mm 1. The largest bearing stress in MPa between the pins and the members; a. 146.23 MPa b. 182.29 MPa c. 174.56 MPa d. 199.37 MPa 2. The average shear stress in MPa in the pin and; a. 108.80 MPa b. 116.14 MPa c. 136.23 MPa d. 98.01 MPa 3. The largest average normal stress in MPa in the members. a. 181.23 MPa b. 175.76 MPa c. 191.26 MPa d. 150.32 MPa
5. Design an oval flanged pipe joint for pipes of internal diameter 50 mm subjected to a fluid pressure of 7 N/mm². The maximum tensile stress in the pipe material is not to exceed 21 MPa and in the bolts 28 MPa. [Ans. 1= 12 mm; d = 30 mm; 1,= 38 mm]
Give me right solution with clear calculations
An engine cylinder is 300 mm in diameter and the steam pressure is 0.7 N/mm2. If the cylinder head is held by 12 studs, find the size. Assume safe tensile stress as 28 MPa.
A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is (350 mm) and the steam pressure is (0.85 MPa) .find the size of the bolt if tensile stress is not to exceed (35 MPa)
The stresses at a point on the surface of a generator shaft are o =-50 MPa, o, = 30 MPa and Try shown in Figure Q3. (Consider only the in-plane stresses. Note: the radius of the = -40 MPa as circle is given by R = ) + ()). Construct the Mohr's circle showing the centre of the circle as well as points A and B. (a) (b) Determine the principal stresses. (c) Show the principal stresses on a sketch of a properly oriented element. (d) Determine the maximum shear stresses. (e) Show the maximum shear stresses on a sketch of a properly oriented element. MPa B. A MPa MPa