Q3 THE Y2 in Roo CE DIAMETER AND TH C DIAMETCR Ro0 DF ARE ATTACHe0 To IN THe Riaio BAR ABCD As SHOWN, BOTH Roos HAVE E = 10,6 X 10°l6/in?, FINO: ) THE FORCE IN CACH ROo 2) THE VERTICAL DEFLECTow OF PoINt A.

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: D Question 2 Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your…

A: Express the force TBC as a vector (in terms of i, j, k). Show all calculations on your paper and…

Q: 4. 1000 inches is how many meters? 5. 450 millimeters is how many inches? 6. A car traveling at a…

A: 1 Inch=0.0254 m1000 Inches=25.4 m1 mm=125.4inch450 mm=45025.4 =17.716 inches

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: L-20 inches d-0.75 inch a-0.1875 inch Ea-10,000 ki Eb-17,000 ki Pa-Pb What is the thickness b?…

A:

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: Find the volume of the given figure. 3ž in. 3 in. 1; in. radius 2 in. radius 7 in. y 2 in 3/4 1/2

A: It is required to determine volume of given section

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: To measure the angles, engineer square is used. Select one: True False

A:

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

A:

Q: What did you put in the calculator to get the box answers? Please put exactly what you put

A: The solution provided in the previous response is as follows.

Q: y Side 3 Side 1 8.0 Side 4 Side 2

A: Plz mention what to do?

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: The outer diameter of cylinder is .The inner diameter of cylinder is .

Q: 0 = 0° A

A:

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: A hollow steel has an outside diameter of 5in. and it's inside diameter is 4in. What is the…

A: Outside diameter, do=5 inInside diameter, di=4 in

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: Figure 5 shows the rod AB rotates clockwise and has an angular velocity and angular acceleration of…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: 14-34. The spring bumper is used to arrest the motion of the 4-lb block, which is sliding toward it…

A: Given Data: The weight of the block is w = 4 lb. The velocity of the block is v = 9 ft/s. The…

Q: R.70 B 4x 1.40 There are 4 arched edges with radius 0.70 inches There are 4 arched edges with…

A:

Q: Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm A 1 cm B 0.5 cm D 6 cm E 0.75 cm F 0.75 cm 0.75…

A: Solution:

Q: Make the indicated conversion between customary and metric units of weight and mass. 17…

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: Express:            50000mm3 as m3 3.5m3 as mm3 20m3 as cm3 45cm3

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.