Q3:- The turning moment curve for an engine is represented by the equation T = 2000 + 950sin20 – 570cos20 N.m where 0 is the angle moved by crank from the inner dead center position. If the resisting torque is constant , find: (1) horsepower developed by the engine, (2) moment of inertia of the flywheel if the total fluctuation of speed is not to exceed 1% of the mean speed which is 180 rpm and (3) angular acceleration of the flywheel when the crank has turned through 45° from its inner dead center nosition

Q3:- The turning moment curve for an engine is represented by the equation T = 2000 + 950sin20 – 570cos20 N.m where 0 is the angle moved by crank from the inner dead center position. If the resisting torque is constant , find: (1) horsepower developed by the engine, (2) moment of inertia of the flywheel if the total fluctuation of speed is not to exceed 1% of the mean speed which is 180 rpm and (3) angular acceleration of the flywheel when the crank has turned through 45° from its inner dead center nosition

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer the question in 5mins I will rate your answer. Cam mechanisms are used in many machines. For example, cams open and close the valves in your car engine to admit gasoline vapor to each cylinder and to allow the escape of exhaust. The principle is illustrated in the figure below, showing a follower rod (also called a pushrod) of mass m resting on a wedge of mass M. The sliding wedge duplicates the function of a rotating eccentric disk on a camshaft in your car. Assume that there is no friction between the wedge and the base, between the pushrod and the wedge, or between the rod and the guide through which it slides. When the wedge is pushed to the left by the force F, the rod moves upward and does something such as opening a valve. By varying the shape of the wedge, the motion of the follower rod could be made quite complex, but assume that the wedge makes a constant angle of ? = 19.0°. Suppose you want the wedge and the rod to start from rest and move with constant…
An engine has a turning moment diagram with the areas above and below the mean torque line of -50 mm2, +120 mm2, -100 mm2, +150 mm2,-80 mm2, +70 mm2 and -110 mm2 with the turning moment diagram scales being for the torque 1mm = 100 Nm and for the crank angle 1mm = 2 °. What is the smallest mass a flywheel of radius of gyration 250mm can have, when running at 600 rpm, if the total fluctuation of speed is not to exceed 2% of the means
The cutting force F in the quick return mechanism shown has a magnitude of 40 N. Neglecting friction, gravity, and inertia, find the driving torque required on link 2 and the bearing forces at 0, and 0, graphically at this configuration. Select proper scales from the figure (rozB = 4 cm). OD6 5 4 2 B2 on 2 Вз on 3 1 3
Ta bh La v ethod Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A and arm B is rotating at 200 rpm ccw. The gears E and F are carried by the arm. The gear G is rigidly attached to shaft C. Find the magnitude and direction of the speed of shaft C. If the gear train is transmitted 7.5 kW what is the torque required to hold shaft A stationary? Given that Z;-40, Z6=30 and Ze=20. B
Orod, leod L Vretative arelative Rp Od Known values: Rp 0.75 m 0.23 m 33 28 6 rad/s 3 rad/s Problem Statement A diak is designed with a peg attached at P As the disk rotates about its center C. the peg slides in the slot of a slotted rod, cauning the rod to rotate about point O. For the instart of interest, key information is provided in the table. Determine the angular motion of the rod and the motion of the peg relative to the rod. Take the senses depicted in the figure as positive. Preletie Be sure to include units with your answers
Please solve and answer the question correctly. Thank you!!
Do neat work
QUESTION 10 A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio 1.62:1. The final chain reduction is 4.7:1 and the effective wheel diameter 0.73 m. Calculate the road speed of the machine in km/h.
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take u = 0.42. Assume uniform wear in clutch.
Q.2 A 75-kW induction motor runs at 740 rpm in clock direction as shown in the figure. A 19 teeth helical pinion with 20 degrees normal pressure angle, 10 mm normal module and a helix angle of 23 degrees is keyed to the motor shaft. Find: a) The transverse pressure angle. b) The pitch diameter of the pinion c) The pitch line velocity. d) Tangential, radial, axial and normal forces on the pinion. 750 200 ZIM 2₁ 19
Solve the problem correctly,Will upvote
J1. In summary, the rotational acceleration of the rollers is 44.02 rad/s2. Using the mass moment of inertia found in step 5, what is the torque required to accelerate the rollers?