Q3: The man is applying a force of 100N to the box. A mass of 300N is placed on an inclined plane as shown in the figure, if you know that us = 0.25 1- Draw the free body diagram (F.B.D) 2- Determine if the block is in equilibrium 3. find the val frietion force

Q: n's Law of Motion odynamics mples (situational or not) from e

A: To give: The summary of Newton's Laws of Motion and Thermodynamics, with some examples.

Q: Define the term form factor?

A: Generally, the word Form factor is defined for the surface finish and tolerance provided over any…

Q: t is the figure called? explain and elaborate

A: The apparatus is a open cup flash point test apparatus

Q: would it be possible to get a detailed explanation? thank you

A:

Q: For the process shown in the schematic below, which of the statements is/are incorrect? Feed hopper…

A: 1)b. The process can only work with thermoplastics and not with thermosets due to the thermal…

Q: 1- A simple introduction. 2- The benefits of this process. 3- The disadvantages of this process. 4-…

A: The mechanical motion of a punch is used to deep draw sheet metal. Under consistent hydrostatic…

Q: can I have FBD for this?

A:

Q: Which of the following is NOT TRUE with respect to the Elastic Transverse Shear Formula?…

A:

Q: If a car weighing 2400 lbs is able to go 1000 ft up a mountain incline whose angle of inclination is…

A: Given data: Weight of car = 2400 lbs                      Distance which car moves up the incline =…

Q: Stanum is vital as mankind enters Stone age New age Brass age Bronze age

A: Correct answer: Bronze age

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: Water flows from a large tank into a 6" diameter pipe through an entrance condition of a square…

A: Given:Pipe diameter, D2=6 inchRadius of the rounded inlet, r=0.12 inchFind:The head loss reduced at…

Q: Name the views that are used to show the part.

A: Engineering drawing is an arrangement of different drawings of a single object viewed from the…

Q: Is this the only correct option in the question above? I think the question is worded for more than…

A: To elaborate why a sling psychrometer can measure humidity.

Q: Figure A. Rectangular block of steel. Adapted from: https://media.wdscomponents.com/ri-…

A: Given: Workpiece is slimmed using slab milling To find: 4 items need to perform slab milling process

Q: A 75 kg diver dives off a 5.2 m high diving board with a speed of 1.5 m/s, with what speed does the…

A:

Q: The beam has a rectangular cross section and is subjected to the loading shown. Determine the state…

A:

Q: What's the worst car ever made?

A: Given Data⇒ worst car Problem statement⇒ Problem says What's the worst car ever made?

Q: Describe the work done is proportional to the force applied (F ) and the distance traveled (s).

A: We know that,Work Done =Force × DisplacementW = F × s From the above equation, If…

Q: Distinguish between the Surface Loads and the Distributed Loads?

A: Load is defined as an external force or a couple to which a member is subjected during its…

Q: So what are the correct answers

A: Explanation: If we consider a system that loses heat δQ at temperature T. Since, In this case the…

Q: Using scientific methods, how would you know the right temperature and heat needed to bake to right…

A: Following steps can be used - With the help of protein denaturation temperature, we can know the…

Q: Explain three pages of laminar flow with the drawing

A:

Q: trenching  machine design and modeling.  Each concept must have an introduction and design…

A: Equipment that is portable and built for small-scale trenching operations is the tiny excavator…

Q: give a steps by steps explanation of the solution

A:

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: ACCURATELY

A: We have given ACCURATELY

Q: A manufacturing company has an order for a specific new product. The order quantity is 45,000 units.…

A:

Q: horwalizing 1) Machinability of low carbon steels improved by: high carbon steel improved by…

A: Heat treatment processes are used to get the desired properties in the metals.

Q: Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square…

A: Write the given data:

Q: Q2: Select any one casted component shown in the figure which is made up of alloy material and used…

A: I will select second one i.e  spiral bevel gear. Alloys used in making gears is zinc alloys  or…

Q: have you figured out part b yet?

A: To determine the magnitude of the reaction force at each bearing, we'll relate the acceleration of…

Q: a BUE? Why does it form?

A:

Q: c. In the field, the position of the interface between oil and water is often difficult to determine…

A:

Q: 6. Low carbon steel can be machined using Abrasive jet machining. 7. Tool life in EDM is infinite.…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…