Q3 / The indicated location of the center of mass of the 1600-kg pickup truck is for the unladen condition. If a load whose center of mass is x = 400 mm behind the rear axle is added to the truck, determine the mass m̟ for which the normal forces under the front and rear wheels are equal. WL |B 1125 1675 mm mm

Q3 / The indicated location of the center of mass of the 1600-kg pickup truck is for the unladen condition. If a load whose center of mass is x = 400 mm behind the rear axle is added to the truck, determine the mass m̟ for which the normal forces under the front and rear wheels are equal. WL |B 1125 1675 mm mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.0m 3.0m 0.5m mi m2 PA N, 5. The drawing above shows two objects on a board supported at two locations. The m; = 40 kg (centered over P), m;=20 kg and m3=10 kg. c. Determine the force exerted by N2. (Take torques around P.) d. m2 rolls to the right. Just before the board starts to tip everything is balanced on N2 with no force on N1. Determine how far to the right of N2 m2 could roll without the board tipping. You might find it easier to take torques around a point rather than P.
1. The cylinder of weight, W (see the table of values), shown below is being hoisted up with the force F against the vertical wall. If u, = 0.57 W W = 500 kn a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion.
The 60 kg two-wheeled cart is described in the figure and parameter table below, with G indicating the location of the center of gravity. It is to be pulled so that it goes up the small step. Find the normal force on each wheel, and the magnitude and direction of the force applied at handle. HINT: remember that there are two wheels sharing the load @080 BY NO SA 2021 Cathy Zupke 4₁1 G L₁ L₂ parameter value 0.6 0.5 0.8 0.7 0.2 A L3 LA d L3 units m m m m m B L₂ F For the answers, take to the right and up to be the positive directions. The normal force at each wheel at A in the x direction is Ax= 150 XN The magnitude of the force at B is F Measured from the positive horizontal axis, the angle of F= 45 X° = 212 XN
SHow important solutions
Last three digits 923
The uniform pole of length l and mass m is placed against the supporting surfaces shown. If the coeffi- cient of static friction is u, = 0.25 at both A and B, determine the maximum angle 0 at which the pole can be placed before it begins to slip. A 105° В 2.
NAME Question 1 (6/20) ANSWER ON THE YELLOW PAGES The nose wheel of the landing gear of an aircraft is extended and retracted by applying a torque M to the rod BC by means of an shaft located at point B. The rod AO, on which the landing wheel is also located, has a combined mass of 100 kg which may be simplified to a point force at point G. The masses of the bars CD and BC may be neglected. If the point D is located underneath point B, the rod CD is at an angle of 30° to the vertical y-axis. At this position the landing gear should be kept stationary, dynamic effects may therefore be neglected. All components are made out of stainless steel with max=200 MPa and Imax = 75 MPa. ALO d. 800 mm 400 mm 200 mm B 300 D M 500 mm OC 500 mm A D Questions, also draw all relevant free-body diagrams: a. Calculate the magnitude of the reaction force at point A. b. Calculate the minimum diameter of the pin in point A. The connection in point A is realized as shown on the right figure. Use a safety…
A tractor is now drafted in to move the blo ck. The weight of the tractor is equally distributed over all four wheels and it pulls on the blo ck via a rope with tension T. The back wheels have a diameter of 1.6m and the front wheelshave a diameter of 80cm. The tractor motor generates a torque of τ on each of its back wheels that have radii Rb and masses mb. The front wheels of the tractor are smaller than the back wheels and have radii Rf and masses mf. Both sets of wheels can b e treated as uniform solid disks with moment ofinertia I = 1/2mR2. The mass of the tractor body, without the wheels, is M. If the wheels don't slip, show that the tractor can accelerate the block with an acceleration of (see image)
A block placed under the head of the claw hammer as shown greatly facilitates the extraction of the nail. If a 40-lb pull on the handle is required to pull the nail, calculate the tension T in the nail and the magnitude A of the force exerted by the hammer head on the block. The contacting surfaces at A are sufficiently rough to prevent slipping. T=? Lb. A=?Lb.
A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller at B on a smooth surface. If the pin support at A suddenly fails, calculate the magnitude of the force of the roller at B acting on the beam at that instant, by modelling the beam as a uniform slender bar. Present your answer in lb using 3 significant figures. 4 13 1000 lb -8 ft- B -2 ft-
Q2/ In the proell governor shown in figure below, the arm ABC is formed in one piece. Each ball has a mass of 1.8 kg and the effect of friction is equivalent to a force of 9N at the sleeve. AB = 150 mm , BC = 50 mm, and BD = 150 mm. Find the magnitude of the central load on the sleeve, if the governor is to rise to its mean position as shown in the diagram when the speed is 120 r.p.m, the portion BC of the lower arm then being vertical. The gravitational effect of the balls must be taken into account. 25 mm B 225 mm 25 mm
While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a horizontal 242-N force on the prybar as shown, what is the horizontal force exerted on rock C? Note that a small ledge on rock C supports a vertical force reaction there. Neglect friction at B. Complete solutions (a) including and (b) excluding the weight of the 17-kg prybar. 242 N A, 1750 mm 15 B 220 mm Answers: (a) Including weight, Fc = i N (a) Excluding weight, Fc = i N